Honda NC700XA Service Manual page 23

dummyhead dummyhead
GENERAL INFORMATION
DUAL CLUTCH TRANSMISSION (DCT) (NC700XD/SD)
ITEM
Solenoid valve stopper plate bolt
Right crankcase cover wire clamp
bolt
Linear solenoid valve body
mounting bolt
Shift spindle angle sensor bolt
Primary drive gear mounting bolt
Reduction gear cover bolt
TR sensor bolt
Shift control motor bolt
Shift drum center bolt
Drum shifter guide plate bolt
Clutch line EOP sensor
EOT sensor
ALTERNATOR/STARTER CLUTCH
ITEM
Flywheel mounting bolt
Starter clutch socket bolt
Alternator stator mounting bolt
Alternator wire clamp bolt
1-18
THREAD
Q'TY
DIA. (mm) N·m (kgf·m, lbf·ft)
1 6
2 6
6 6
1 6
1 10
3 6
1 6
3 6
1 8
2 6
3 10
1 10
THREAD
Q'TY
DIA. (mm) N·m (kgf·m, lbf·ft)
1 12 157 (16.0, 116)
6 8
4 6
1 6
TORQUE
12 (1.2, 9) Apply locking agent to the threads.
Coating width: 6.5 ± 1.0 mm (0.26 ±
0.04 in) except 2.0 ± 1.0 mm (0.08 ±
0.04 in) from tip
12 (1.2, 9) Apply locking agent to the threads.
Coating width: 6.5 ± 1.0 mm (0.26 ±
0.04 in) except 2.0 ± 1.0 mm (0.08 ±
0.04 in) from tip
– For tightening sequence (page 12-
101)
12 (1.2, 9)
93 (9.5, 69) Apply engine oil to the threads and
seating surface.
14 (1.4, 10)
12 (1.2, 9)
14 (1.4, 10)
23 (2.3, 17) Apply locking agent to the threads.
Coating width: 6.5 ± 1.0 mm (0.26 ±
0.04 in) except 2.0 ± 1.0 mm (0.08 ±
0.04 in) from tip
12 (1.2, 9) Apply locking agent to the threads.
Coating width: 6.5 ± 1.0 mm (0.26 ±
0.04 in) except 2.0 ± 1.0 mm (0.08 ±
0.04 in) from tip
19.6 (2.0, 14)
14 (1.4, 10) Apply engine oil to the threads and
seating surface.
TORQUE
Left hand thread
Apply engine oil to the threads and
seating surface.
30 (3.1, 22) Apply locking agent to the threads.
Coating width; 6.5 ± 1.0 mm (0.26 ±
0.04 in) except 2.0 ± 1.0 mm (0.08 ±
0.04 in) from tip
10 (1.0, 7) Apply locking agent to the threads.
Coating width; 6.5 ± 1.0 mm (0.26 ±
0.04 in) except 2.0 ± 1.0 mm (0.08 ±
0.04 in) from tip
10 (1.0, 7) Apply locking agent to the threads.
Coating width; 6.5 ± 1.0 mm (0.26 ±
0.04 in) except 2.0 ± 1.0 mm (0.08 ±
0.04 in) from tip
REMARKS
REMARKS