Honda NC700XA Service Manual page 21

dummyhead dummyhead
GENERAL INFORMATION
MAINTENANCE
ITEM
Air cleaner housing cover screw
Spark plug
Valve adjusting screw lock nut
Camshaft maintenance cap
Timing hole cap
Crankshaft hole cap
Engine oil drain bolt
Engine oil filter cartridge
Oil filter boss
Rear axle nut
Drive chain adjuster lock nut
Drive sprocket bolt
Driven sprocket nut
Master cylinder reservoir cover
screw
Rear brake reservoir mounting bolt
Rear master cylinder push rod lock
nut
Parking brake adjuster bolt lock
nut (NC700XD/SD)
Sidestand pivot bolt
Sidestand pivot nut
Sidestand switch bolt
PGM-FI SYSTEM
ITEM
ECT sensor
Bank angle sensor mounting bolt
O sensor
2
IGNITION SYSTEM
ITEM
Timing hole cap
Right crankcase cover wire clamp
bolt (NC700XD/SD)
ELECTRIC STARTER
ITEM
Starter motor terminal nut
FUEL SYSTEM
ITEM
Fuel pump mounting nut
Air cleaner connecting hose band
screw
Insulator band screw
1-16
THREAD
Q'TY
DIA. (mm) N·m (kgf·m, lbf·ft)
6 5
2 14
8 7
1 36
1 14
1 30
1 12
1 20
1 20
1 18
2 8
1 10
5 12 108 (11.0, 80)
4 4
1 6
1 8
1 8
1 10
1 10
1 6
THREAD
Q'TY
DIA. (mm) N·m (kgf·m, lbf·ft)
1 10
2 6
1 12
THREAD
Q'TY
DIA. (mm) N·m (kgf·m, lbf·ft)
1 14
2 6
THREAD
Q'TY
DIA. (mm) N·m (kgf·m, lbf·ft)
1 6
THREAD
Q'TY
DIA. (mm) N·m (kgf·m, lbf·ft)
6 6
1 4
2 5
TORQUE
1.1 (0.1, 0.8)
22 (2.2, 16)
14 (1.4, 10) Apply engine oil to the threads and
seating surface.
4.0 (0.4, 3.0) See page 3-12
10 (1.0, 7) Apply grease to the threads.
15 (1.5, 11) Apply grease to the threads.
30 (3.1, 22)
26 (2.7, 19) Apply engine oil to the threads.
– See page 3-14
Apply locking agent to the threads.
Coating width; 6.5 ± 1.0 mm (0.26 ±
0.04 in) from tip
98 (10.0, 72) U-nut
21 (2.1, 15)
54 (5.5, 40)
U-nut
1.5 (0.2, 1.1)
10 (1.0, 7)
17 (1.7, 13)
17 (1.7, 13)
– See page 3-27
Apply grease to the sliding surface.
39 (4.0, 29) U-nut
10 (1.0, 7) ALOC bolt; replace with a new one.
TORQUE
12 (1.2, 9)
10 (1.0, 7)
24.5 (2.5, 18)
TORQUE
10 (1.0, 7) Apply grease to the threads.
12 (1.2, 9) Apply locking agent to the threads.
Coating width; 6.5 ± 1.0 mm (0.26 ±
0.04 in) except 2.0 ± 1.0 mm (0.08 ±
0.04 in) from tip
TORQUE
10 (1.0, 7)
TORQUE
12 (1.2, 9) For tightening sequence (page 7-14)
1.5 (0.2, 1.1)
– See page 7-18
REMARKS
REMARKS
REMARKS
REMARKS
REMARKS