Honda CR-V 1997 Service Manual page 691

CD
ENDCDVER
®
OIL SEAL Replace.
@) BALL BEARING
@
AIT GEAR POSITION SWITCH COVER
®
AIT GEAR POSITION SWITCH
®
ROLLER
(J) COLLAR
@ C-RING Replace.
®
FEED PIPE FLANGE
@J
D-RING Replace.
(jj) SNAP RING
@
3RD CLUTCH FEED PIPE
@ COUNTERSHAFT LOCKNUT 23 x 1.25 mm Replace.
@ CONICAL SPRING WASHER Replace.
@
PARK GEAR
@ ONE-WAY CLUTCH
@ COUNTERSHAFT 1ST GEAR
@ NEEDLE BEARING
@
COUNTERSHAFT 1ST GEAR COLLAR
®
O-RING Replace.
@
1ST CLUTCH FEED PIPE
@ C-RING Replace.
®
FEED PIPE FLANGE
®
SNAP RING
@ DOWEL PIN
@ END COVER GASKET Replace.
®
PARK PAWL STOP
@
PARK PAWL
®
PARK PAWL SPRING
®
PARK PAWL SHAFT
@ AIT GEAR POSITION SWITCH HARNESS CLAMP
@
PARK LEVER
@ LOCK WASHER Replace.
@
PARK STOP Selective part
@ PARK LEVER SPRING
®
DRAIN PLUG
@ SEALING WASHER Replace.
,~
MAINSHAFT LOCKNUT 21
x
1.25
mm
Replace.
@ CONICAL SPRING WASHER Replace.
@ 1 ST CLUTCH ASSEMBLY
TORQUE SPECIFICATIONS
Bolt/Nut No.
Torque Value
6A
12 N·m 11.2 kgf-m, 8.7IbHt)
68
14 N'm (1.4 kgf·m, 10 IbHt)
8A 22 N-m (2.2 kgf·m, 161bHt)
12J
28 N·m (2.9 kgf·m, 21 IbHt)
180
49 N·m (5.0 kgf-m, 36 IbHt)
195 93 N-m (9.5 kgf·m, 69 IbHt)
21M
78 N-m (8.0 kgf·m, 58 Ibf·ft)
23C
103 - 0 - 103 Nm (10.5 - 0 - 10.5 kgfm,
75.9 - 0 - 75.9 IbHt)
@ O-RING Replace.
@ THRUST WASHER
@ THRUST NEEDLE BEARING
@ NEEDLE BEARING
@ MAINSHAFT 1ST GEAR
@
MAINSHAFT 1 ST GEAR COLLAR
@
C-RING Replace.
@ COUNTERSHAFT SPEED SENSOR
@
ROLLER
®
COLLAR
®
O-RING Replace.
@ FEED PIPE FLANGE
@: C-RING Replace.
®
SNAP RING
®
1ST-HOLD CLUTCH FEED PIPE
~
SUB-SHAFT LOCKNUT 19 x 1.25 mm Replace.
@
CONICAL SPRING WASHER Replace.
@ SUB-SHAFT 1ST GEAR
®
LINEAR SOLENOID ASSEMBLY
@ LINEAR SOLENOID ASSEMBLY GASKET Replace.
@ HARNESS BRACKET
@ SEALING WASHERS Replace.
@
ATF COOLER LINE
®
LINE BOLT
®
ATF DIPSTICK
@
ATF COOLER LINE
@
LINE BOLT
@ SEALING WASHERS Replace.
®
VEHICLE SPEED SENSOR IVSSI
®
C-RING Replace.
Size
Remarks
6x 1.0mm
6x 1.0 mm
ax 1.25mm
12x 1.25mm
Line bolt
18 x 1.5 mm Drain plug
19 x 1.25 mm
Sub-shaft locknut
21 x 1.25 mm
Mainshaft locknut: Left-hand threads
23 x 1.25 mm
Countershaft locknut: Left-hand
threads
14-175