Honda CR-V 1997 Service Manual page 504

78mmSHIM
Pert Number
A
23941 - P16- 000
B
23942 - PI 6 -000
C
23943 - P16 - 000
D
23944 - PIS - 000
E
23945 - P16 - 000
F
23946 - PI 6 - 000
G
23947 - PI 6 - 000
H 23948 - P16 - 000
I 23949 - P16 - 000
J
23950 - PIS - 000
K 23951 - P16 - 000
L
23952 - P16 - 000
M
23953 - PIS - 000
N
23954 - P16 - 000
0
23955 - PIS - 000
P 23955 - P16 - 000
Q 23957 - P16 - 000
R
23958 - PI 6 - 000
5 23959 - P16 - 000
T 23950 - PI 6 - 000
U
23961 - P16 - 000
V 23962 - P16 - 000
W
23963 - P16 - 000
X
23954 - P16 - 000
y
23955 - P16 - 000
Z
23965 - PIS - 000
AA
23967 - P16 - 000
AB
23958 - P16 - 000
AC
23959 - P16 - 000
AD
23970 - PIS - 000
AE
23971-P1S-000
AF
23972 - PIS - 000
AG
23973 - PIS - 000
AH
23974-P1S-000
AI
23975 - PIS - 000
AJ
23976 - PIS - 000
AK
23977 - PIS - 000
AL 23978 - PIS - 000
AM 23979 - PIS - 000
AN
23980 - PIS - 000
Thickness
1.20 mm (0.0472 in)
1.23 mm 10.0484 in )
1.26 mm (0.0496 in)
1.29 mm 10.0508 in)
1.32 mm (0.0520 in)
1.35 mm (0.0531 in)
1.38 mm (0.0543 in)
1.41 mm (0.0555 in)
1.44 mm (0.0567 in)
1.47 mm (0.0579 in)
1.50 mm 10.0591 in)
1.53 mm 10.0602 in)
1.56 mm 10.0614 in)
1.59 mm 10.0626 in)
1.62 mm (0.0638 in)
1.65 mm (0.0550 in)
1.68 mm (0.0561 in)
1.71 mm 10.0573 inl
1.74 mm 10.0685 in)
1.77 mm (0.0697 in)
1.80 mm 10.0709 inl
1.83 mm 10.0720 in)
1.86 mm (0.0732 in)
1.89 mm (0.0744 in)
1.92 mm (0.0755 in)
1.95 mm 10.0768 in)
1.98 mm 10.0780 in)
2.01 mm 10.0791 in)
2.04 mm 10.0803 in)
2.07 mm (0.0815 in)
2.10 mm (0.0827 in)
2.13 mm 10.0839 in)
2. IS mm 10.0850 in)
2.19 mm (0.0852 in)
2.22 mm (0.0874 in)
2.25 mm 10.0885 in)
2.28 mm 10.0898 in)
2.31 mm (0.0909 in)
2.34 mm (0.0921 in)
2.37 mm 10.0933 in)
7. Check the thrust clearance in the manner described
below.
NOTE: Measurement should be made at normal
room temperature.
-1. Install the 78 mm shim selected and oil guide
plate in the transmission housing.
78mmSHIM
OIL GUIDE PLATE
-2. Install the spring washer and washer on the
ball bearing.
NOTE:
• Clean the spring washer, washer and thrust
shim thoroughly before installation.
• Install the spring washer, washer and thrust
shim properly.
WASHER
~ '
SPRING WASHER
me!:>
-3. Install the mainshaft in the clutch housing.
-4. Place the transmission housing over the main-
shaft and onto the clutch housing.
-5. Tighten the clutch and transmission housings
with several 8 mm bolts.
NOTE: It is not necessary to use sealing agent
between the housings.
-6. Tap the mainshaft with a plastic hammer.
(cont'd)
13-65