Honda CR-V 1997 Service Manual page 34

At
t· T
Sect·
14
Unit of length: mm (in)
- U oma Ie ransmlsslon - Ion
MEASUREMENT STANDARD INEW)
SERVICE LIMIT
Transmission Mainshaft 2nd gear thrust washer thickness 3 .97 - 4.00 10.156- 0 .157 ) Wear or damage
4.02 - 4.0510.158 - 0 .159)
4.07 - 4.10 10.160 - 0 .161)
4.12-4.1510.162-0.163)
4.17 - 4.20 10.164 - 0 .165)
4.22 - 4.25 10.166 - 0.167)
4.27 - 4.30 10.168 - 0.1691
4.32 - 4.35 10.170 - 0.171)
4.37 - 4.40 10.172 - 0.173)
4.42 - 4.4510.174 - 0 .175) Wear or damage
Thrust washer thickness
Mainshaft ball bearing left side 2.95 - 3.05 10.116 - 0.120) Wear or damage
Mainshaft 1st gear 2.43 - 2.50 10.096 - 0 .098)
t
Countershaft 3rd gear splined washer
4.95 - 5.00 10.195 - 0.1971
SUb-shaft 4th gear thrust washer
2.93 - 3.00 10.115 - 0.118) Wear or damage
One-way clutch contact area 1.0.
Countershaft 1st gear 83.339 - 83.36513.2810 - 3.28211 Wear or damage
Parking gear 66.585 - 66.69812 .6254 - 2.6259) Wear or damage
Mainshaft feed pipe A, 0.0. (at 15 mm from end)
8.97 - 8.9810.353 - 0 .354) 8.95 10.352)
Mainshah feed pipe B, 0.0. (at 30 mm from end)
5.97 - 5.9810.2350 - 0.2354) 5 .9510.234)
Countershaft feed pipe D.O. (at 15 mm from end)
7 .97 - 7.98 10.3 138 - 0.3142) 7 .9510.313)
Sub-shaft feed pipe 0.0. (at 15 mm from end)
7.97 - 7.9810.3138 - 0.3142) 7.9510.313)
Mainshaft sealing ring thickness
1.87 - 1.9710.074-0.078) 1.82 10.072)
129
mm
and 35 mm)
Mainshaft bushing LO.
6.018 - 6.030 10.2369 - 0 .2374) 6 .045 10.2380)
Mainshaft bushing 1.0. 9.000 - 9.01510.3543 - 0.3549) 9.03 10.356)
Countershaft bushing 1.0. 8.000 - 8.022 10.3150 - 0.31 58) 8.0310.316)
Sub-shaft bushing 1.0. 8.000 - 8.02210.3150 - 0.3158)
8.0310.316)
Mainshaft sealing ring groove width 2.025 - 2.07510.0797 - 0 .0811) 2.095 10.082)
ATF pump
ATF pump gear side clearance 0.03 - 0.0510.001 - 0.002) 0.07 10.003)
ATF pump gear-to-body clearance
Drive
0.1050 - 0.1325 10.004 - 0.005)
- -
Driven 0.0350 - 0.0625 10.001 - 0.002)
- -
ATF pump driven gear 1.0. 14.016 - 14.034 10.5518 - 0.5525)
Wear or damage
ATF pump driven gear shaft 0.0. 13.980 - 13.99010.5504 - 0.5508) Wear or damage
Regulator
Sealing ring contact area 1.0. 35.000 - 35.025 11.3780 - 1.3782 ) 35.050 (1.3799)
valve body
Stator shaft Inside of diameter of bearing contact area
On torque converter side 27.000 - 27.021 11.063 - 1.064) Wear or damage
On ATF pump side 29.000 - 29.013 11.1417 - 1.1422) Wear or damage
Shifting device and Reverse shift fork finger thickness 5.90 - 6 .00 10.232 - 0.236)
5.4010.213)
parking brake con- Parking brake pawl
- -
} Wear or other defect
trol Parking gear
- -
Servo body Shift fork shaft bore 1.0. 14.000 - 14.010 10.5512 - 0.5516)
- -
Shift fork shaft valve bore 1.0, 37.000 - 37.039 (1.4567 - 1.4582) 37.04511.4585)
Differential Pinion shaft contact area 1.0.
18.010 - 18.02810.709 - 0.7 10)
--
carrier Carrier-to-pinion shaft clearance
0.023 - 0.057 10.001 - 0.002) 0.1 10.004)
Driveshaftlintermediate shaft contact are 1.0. 2WD 26.025 - 26.045 11.0246 - 1.0254)
- -
4WD 28.025 - 28.045 11.103 - 1.104)
- -
Carrier-to-driveshaft clearance 0.045 - 0.08610.002 - 0.003) 0.1210.005)
Carrier-to-intermediate shaft clearance 0.075 - 0.111 10.003 - 0.004) 0.1510.006)
Differential Backlash 0.05 - 0.15 10.002 - 0.006)
- -
pinion gear !.D. 18.042 - 18.066 10 .7103 - 0.7113)
- -
Pinion gear-to-pinion shaft clea rance 0.055 - 0.09510.0022 - 0.0037 ) 0.1510.006)
Set ring-to-bearing outer race clearance
0- 0.15 10 - 0 .006)
Adjust
Transfer Diameter of roller bearing contact area
Transfer shaft (transfer g ear side) 38.485 - 38.500 11 .515 - 1.516)
38.4311 .513)
Transfer shaft (middle of shaft) 27.977 - 27 .990 11 .101 - 1.102) 27.92 (1.099)
Transfer drive gear 40.002 - 40.01811 .575 - 1.576) 39.9511 .573)
Transfer driven gear shaft (driven gear side)
35.002 - 35.01811 .378 -1 .379) 34.95 (1 .376)
Transfer driven gear shaft (splined side) 26.975 - 26.98811.062 - 1.063) 26.92 11.060)
Transfer gear backlash 0.060 - 0.16010.002 - 0.006)
Adj ust
Total starting torque N·m (kgf-cm , Ibf-in ) 2.68 - 3.47
Adjust
127.3 - 35.4, 23.7 - 30.7)
Icont d)
2-9