Honda CR-V 1997 Service Manual page 31

Standards and Service Limits
; -
M
anual Transmission (cont' d J-
s
ection 13
MEASUREMENT STANDARD INEW) SERVICE LIMIT
Reverse shift fork Pawl groove width
13.0 - 13.3 10.51 - 0.52)
- -
Fork-ta-reverse idler gear clearance
0.5 - 1.1 10.02 - 0.04) 1.8 (0.07)
Groove width*l
at A
7.05 - 7.25 (0.278 - 0.285)
- -
al B
7.4 - 7.7 (0.29 - 0.30)
- -
Fork-to-5th/reverse shift shaft clearance-1-2
at A'
0.05 - 0.35 (0.002 - 0.014)
0.510.02)
at 8'
0.4 - 0.8 (0.02 - 0.03) 1.0 (0.04)
Shift
arm
A Shift fork diameter at contact area 12.9 - 13.0 10.508 - 0.5121
- -
Shift arm A-ta-shift fork shaft clearance
0.2 - 0.5 (0.008 - 0.020) 0.6 (0.024)
Shift
arm
C Shift
arm
C-to-shift arm B clearance
0.05 - 0.25 (0.002 - 0.01)
- -
Diameter of shift arm B contact area
12.9 - 13.0 (0.508 - 0.5121
- -
Select arm
Select arm-te-shift arm A clearance
0.05 - 0.2510.002 - 0.01)
- -
Diameter of shift arm A contact area
7.9 - 8.0 (0.311 - 0.315)
- -
Select lever
D.D. 15.941 - 15.968 (0.6276 - 0.6287)
- -
Transmission housing clearance
0.032 - 0.086 (0.0013 - 0.0034)
- -
Shift lever
D.D.
15.941 - 15.968 10.6276 - 0.6287)
- -
Shift arm cover clearance
0.032 - 0.127 (0.0013 - 0.0050)
- -
Differential
Pinion shaft contact area 1.0. 18.010 - 18.028 (0.7091 - 0.7098)
- -
carrier
Carrier-ta-pinion shaft clearance 0.027 - 0.057 (0.0011 - 0.0022) 0.1 (0.004)
Driveshaft, intermediate shaft contact area 1.0. 28.005 - 28.025 (1.1026 - 1.1033)
- -
Carrier-to-driveshaft clearance
0.025 - 0.066 (0.0010 - 0.0026) 0.12 10.005)
Carrier-to-intermediate shaft clearance 0.055 - 0.091 10.0022 - 0.0036) 0.15 10.006)
Differential
Backlash
0.05 - 0.15 10.002 - 0.006)
- -
pinion gear
I.D. 18.042 - 18.066 (0.7103 - 0.7113)
- -
Pinion gear-to-pinion shaft clearance 0.059 - 0.095 10.0023 - 0.0037) 0.15 10.006)
Differential tapered roller bearing preload
1.4 2.5114
26,12 23)
Adjust
Starting torque N·m (kgf'cm, IbNn)
Transfer Diameter of roller bearing contact area
Transfer shaft (driven gear side)
33.984 - 34.000 (1.337 - 1.339) 33.93 (1 .3361
Transfer shaft (middle of shaft)
27.977 - 27.990 (1.101 - 1.102)
27.92 (1.099)
Transfer drive gear
40.002 - 40.01811.575 - 1.576) 39.95 (1.573)
Transfer driven gear shaft (driven gear side)
35.002 - 35.01811.378 - 1.379)
34.95 (1.376)
Transfer driven gear shaft (splined side) 26.975 - 26.98811.062 - 1.063) 26.92 (1.060)
Transfer gear backlash
0.06 - 0.1610.002 - 0.006)
Adjust
Total starting torque N'm (kgf.cm, Ibf·in)
2.68 - 3.47
Adjust
127.3 - 35.4, 23.7 - 30.7)
*1: Measuring points A
~.
*2: Measuring points
A'
~
2-6