Siemens SIMOCODE pro System Manual page 656

Index
Basic unit connection example
Basic unit inputs 7-3, 7-4
Basic unit outputs 6-4
Basic unit pin assignment
Basic units 1-29, C-2
Baud rate 1-72, Glossary-2
Baud rates up to 12 MBit/s
Binary inputs for 110 - 240 V AC/DC
Binary inputs on the basic units and digital
modules 7-1
Binary terminal block
Bistable outputs 1, 2
Bistable relay outputs
BU input settings 7-5
BU inputs 1-121
BU outputs 1-121, 6-5
Bus Glossary-2
Bus connection D-8
Bus connection system
13-31
Bus connection system from 20 A to
630 A 13-30, 13-31
Bus fault/PLC/PCS fault response
Bus monitoring 1-72, 10-24, 10-25
Bus o.k. 1-72
Bus ok, PLC/PCS in run
Bus parameters 12-1
Bus segment Glossary-2
Bus termination module
Bus/PLC fault - reset
Buttons, operator panel
Buttons, operator panel with display
C
Cable cross sections
Cable length of the sensor circuit
cables F-6
Cable protection F-6
Calculation modules
Calculator 1-21
Calculator 1 1-59, 1-70, 1-117
Calculator 2 1-59, 1-71, 1-117, 11-28
Calculator examples
Calculator formulae
Calculator settings 11-29
Calculators 1-70
Cascade input Glossary-2
Cascade input automatic start/monitored
start 10-21
Catalogs and information material
F-10
Change-over pause
4-32, 4-34, 4-36, 4-37, 4-39, 4-41, 4-43,
4-44, 4-46, 4-48, 4-50
Change-over pause active
Channel-related diagnostics
Index-2
13-15
13-14
1-20
1-14
1-112
1-77
1-14
1-24, 13-30,
10-25
1-63
13-47
1-73, 10-25
D-22
D-23
13-12
1-21, 11-2
11-30
11-29
xiii,
4-16, 4-18, 4-31, 4-
1-64
12-7, 12-14
Characteristic curve of a type A sensor
F-5
Check list for selecting a device series
1-13
Circuit breaker 1-19, 4-14, 4-29
Circuit breaker control (MCCB)
Class 3-8, Glossary-2
Class 1 master 12-2, 12-17, Glossary-2
Class 2 master 12-2, Glossary-2
Class time 3-14
Clear 1-85
Clockwise rotation 4-33
Cold starting 10-9
Color coding for the connecting cable
13-41, 13-43
Commands 1-52
Commands (OPD) 1-48
Comment 1-89
Commissioning 2-9, 14-1, 14-3, 14-4, F-3
Communication 1-5, 1-20, 1-51, 12-1
Communication principle
Compatibility mode
Compatibility mode 1
Conductor cross section
Configuration fault 15-2
Configuration information for using an ope-
rator panel with display and/or a decou-
pling module 1-106
Configure diagnostic response
Configuring a reversing starter
Configuring the DM-F DIP switch
Connecting cable 1-27, 1-108, 13-36,
Glossary-3
Connecting cables to the system interface
of the operator panel
Connecting plugs with sockets
Connecting system components to the
system interface 13-39, 13-43
Connecting the PROFIBUS DP to the
9-pole SUB-D socket
Connection cross sections, decoupling
module D-9
Connection for voltage measurement
D-8
Connection, analog module
Connection, basic units
Connection, digital modules
Connection, DM-F D-13
Connection, earth-fault module
Connection, temperature module
Contactor Glossary-3
Contactor control 4-33
Contactor controls 4-12, 4-65, A-2
Contrast 1-81
Control circuit, analog module
Control circuit, digital modules
GWA 4NEB 631 6050-22 DS 03
1-30
12-4
1-73
1-74
13-30, 13-31
12-7
2-1
1-101
13-44, 13-45
1-113
13-46
D-20
D-6
D-11
D-20
D-21
D-19
D-10
SIMOCODE pro