YASKAWA NX100 Instructions Manual page 305

G
GAS SHORTAGE (MONITOR)
.............................................
grounding
group (4-bit/8-bit) output allocation
group output allocation (4-bit/8-bit)
GUN COOLING WATER ERROR
GUN FULL OPEN DETECTION
GUN PRESSURE DETECTION
GUN SHORT OPEN DETECTION
H
............................................
HAND VALVE
.......................................
handling procedure
...............................................
home position
home position calibration
home position of the robot
how to calculate tool load information
I
I/O circuit board (JANCD-NIO01)
..............................................
I/O diagnosis
............................................
I/O instructions
................................................
I/O modules
........................................
inching operation
...............................
INERTIA RATIO
.............................................
initial diagnosis
........................................
initialize data file
..........................................
initialize job file
initialize parameter file
......................................
initializing I/O data
initializing system data
installation and wiring safety
............................
instruction allocation
...........................................
instruction level
instruction of shock detection function
.............................................
instruction set
.....................................................
interface
.........................................
interference area
J
JANCD-XEW02 circuit board (standard)
.......................................................
job call
........................................
job call allocation
K
key allocation (EACH)
.....................................
key allocation (SIM)
....................
13-43
1-6 , 12-2
................
8-96
................
8-88
................
13-60
..................
13-61
..................
13-61
...............
13-61
13-49
3-1
8-3
...............................
8-1
..............................
8-9
............
8-37
.................
13-13
12-4
12-4
11-1
12-3
11-14 , 11-23
5-2
8-105
8-104
................................
8-106
8-107
................................
8-108
..........................
1-6
8-87 , 8-90
8-80
...........
8-64
8-80
12-3
8-49
.......
13-64
8-92
8-87
.................................
8-87
8-87
L
.....................................................
language
...........................................................
L-axis
leakage breaker installation
learning function
lifting the NX100
..................................................
limit switch
LOW AIR PRESSURE
L-U interference
M
...............................................
machine lock
maintenance input
major axes control circuit board (SGDR-AXA01A)
13-13
major axes control circuit boards
managememt mode
manufacturer allocation
max. disturbance force
......................................
MAX. RPM
measurement of the tool load and the center of grav-
...............................................................
ity
mechanical limit
MECHANICAL SPEC window
memory capacity
method of the tool load information setting
modification of system configuration
modification of teaching points
momentary output allocation
MOTION RANGE
MOTOR SPEC display
moving the MOTOMAN
N
....................................................
noise filter
number of tool files
numeric key customize function
.........................................................
NX100
O
...................................................
operating
operation instructions
operation mode
operation time display
................................................
order number
...........................................................
ORG
output of the work home position signal
overrun releasing
Index-2
...........................
..........................................
...........................................
......................
13-48 , 13-60
...........................................
...........................
13-23 , 13-31
...................
......................................
................................
.................................
11-14 , 11-23
...........................................
.....................
..........................................
..............
......................
................
8-88 , 8-95
.......................................
...............................
................................
.......................................
.....................
...................................
............................................
..................................
.........
.........................................
12-4
6-3
4-4
8-81
1-7
8-77
8-78
12-3
..
13-9
7-1
8-87
8-63
8-28
8-78
11-12
12-2
.....
8-64
11-1
12-3
11-12
11-14
1-14
4-4
8-17
8-87
1-8
13-15
12-4
7-1
12-4
2-2
8-70
8-48
8-75