Bosch Rexroth IndraDrive Troubleshooting Manual page 423
Hide thumbs
Also See for Rexroth IndraDrive:
- Applications manual (100 pages) ,
- Project planning manual (128 pages) ,
- Instruction manual (26 pages)
Table of Contents
Advertisement
13-6
Index
LSA Control S.L. www.lsa-control.com comercial@lsa-control.com (+34) 960 62 43 01
Timeout during loading process 7-27
Undervoltage in mains 7-120, 8-42
Undervoltage in power section 7-86, 8-20
Unknown operating mode 6-36
Watchdog 7-4
Homing of absolute encoder not possible 9-72
Homing only possible with drive enable 9-70
Homing procedure command channel 2 9-17
HW control braking resistor 8-40
I
IBF not correct! 4-3
ID9 + Record length - 1 > length MDT (S-0-0010) 9-23
Inappropriate use 2-2
Consequences, Discharge of liability 2-1
Incorr. parameteriz. of motor enc. (mechanical system) 9-28
Incorr. parameteriz. of opt. enc. (mechanical system) 9-31
Incorr. prarmeterization of measuring enc. (hardware) 9-46
Incorrect access to command value memory 7-109
Incorrect backup of safety technology data 7-74
Incorrect direction of motion 7-36
Incorrect I/O length 7-54
Incorrect input for current 9-112
Incorrect input for frequency 9-113
Incorrect input for power 9-115
Incorrect input for power factor 9-114
Incorrect input for speed 9-114
Incorrect input for voltage 9-113
Incorrect measuring encoder configuration 9-48
Incorrect parameterization of motor encoder (hardware) 9-27
Incorrect parameterization of optional enc. (hardware) 9-31
Incr. encoder emulator
hardware fault 7-101
pulse frequency too high 7-100
Incremental enc. emulator resol. cannot be displayed 9-67
Inertia detection failed 9-94
Initialization velocity encoder 1 too high 9-53
Initialization velocity encoder 2 too high 9-55
Initialization velocity measuring encoder too high 9-57
interface error
commissioning 7-49
Interpolation acceleration = 0 8-23
Interpolation velocity = 0 8-22
Invalid communication phase shutdown 7-52
Invalid control section data (->S-0-0021) 9-39
Invalid control section data (->S-0-0022) 9-51
Invalid control section/firmware combination 7-21
Invalid motor data in encoder memory (->S-0-0021) 9-36
Invalid parameters (-> S-0-0021) 9-17
Invalid parameters (->S-0-0022) 9-49
Invalid power section/firmware combination 7-20
Invalid settings for controller cycle times 9-35
It was impossible to address EnDat memory 7-112
It was impossible to address I2C memory 7-111
It was impossible to address MMC 7-110
K
kind of diagnostic message
commands 1-18
error 1-16
states/operating states 1-18
warnings 1-17
kinds of diagnostic messages 1-1
L
language selection 1-4
LB 5-2
Rexroth IndraDrive
DOK-INDRV*-GEN-**VRS**-WA01-EN-P
- Quick Links:
- Coded Diagnostic Drive Messages
- Error
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the Rexroth IndraDrive and is the answer not in the manual?
Questions and answers
Our machine in Rexroth drive installation total 20 nos machine so facing issue shortly 5 drive folty 8060 erro so how to do
Error 8060 on Bosch Rexroth IndraDrive indicates an overcurrent in the power section. To resolve this issue for five machines, follow these steps for each machine:
1. Check the Load and Connections – Verify that the motor and power connections are correct and not causing excessive current draw.
2. Inspect the Power Section – Look for any visible damage or overheating signs in the power section.
3. Restart the System – Power off the drive, wait for the DC bus to discharge below 50V, and restart.
4. Adjust Parameters if Needed – Ensure that the drive’s current limits and motor settings are correctly configured.
5. Replace Faulty Components – If the issue persists, the power section may be defective and require replacement.
Repeat these steps for all five machines to ensure proper operation.
This answer is automatically generated
What is solution of 2110 fault in rexroth drive
The solution for the F2110 fault in Bosch Rexroth IndraDrive is:
1. If the failure occurs sporadically (firmware error), clear the error and contact the service department for a firmware update.
2. If the error occurs repeatedly, it indicates defective hardware. In this case, the control section or the entire device must be replaced.
3. Only Rexroth service engineers or specially trained users are allowed to replace the control section.
4. The procedure for replacing the entire drive controller is described in the Project Planning Manual for the power section.
This answer is automatically generated
The engine moves in manual mode but does not work in automatic mode. The error code is E2074. What should I do?
Error code F2074 indicates a defective motor encoder. To resolve this issue:
1. Check the position data reference – If the position data reference is incorrect, the encoder is defective.
2. Replace the motor or motor encoder – A faulty encoder can prevent movement in automatic mode.
3. Send the motor to the manufacturer’s service department for inspection.
If the issue persists, consult the service department for further assistance.
This answer is automatically generated
@Aleksand C0209incorrect encoder configuration error on drive controller display, red light fickering on drive comms port,
Please help me with the problem of the VM F2802 and E2810 errors on the Rexroth Indradrive M
The VM F2802 error on the Bosch Rexroth IndraDrive M indicates that the Phase-Locked Loop (PLL) is not synchronized.
The E2810 error means that the drive system is not ready for operation. This occurs when one or more drives in a system (connected via DC bus and module bus) signal an error, preventing the supply from being ready for power output. To resolve it, identify the drives signaling an error and remove the cause, or ensure all drives are in communication phase 4.
This answer is automatically generated
Medodyjsjddidi