Replacing The Motor; Replacing Cables - Bosch Rexroth IndraDrive Troubleshooting Manual
Hide thumbs
Also See for Rexroth IndraDrive:
- Applications manual (100 pages) ,
- Project planning manual (128 pages) ,
- Instruction manual (26 pages)
Table of Contents
Advertisement
10-12
Handling, Diagnostic and Service Functions
Replacing the Motor
Replacing Cables
LSA Control S.L. www.lsa-control.com comercial@lsa-control.com (+34) 960 62 43 01
• Switch main switch off.
• Make sure main switch cannot be switched on again.
• Disconnect plug-in connectors.
Note:
When replacing the motor, cap open connector ends
particularly if there might be the chance that they get in contact
with coolant/lubricant or dirt (allowed level of contamination is
2 according to EN50178).
• Replace motor.
Note:
To mechanically replace the AC servo motor, note the
instructions of the machine manufacturer.
• Connect plug-in connectors.
Danger caused by unwanted axis motion!
⇒ Servo axes with indirect path measuring system via
the motor encoder will loose the reference dimension
when the motor is replaced!
ATTENTION
This reference to the machine coordinate system
must therefore be reestablished after replacement.
• Servo axes with absolute motor encoder: reestablish the reference
dimension.
Lethal electric shock caused by live parts with
more than 50 V!
⇒ Power connectors of the cables may only be
separated or connected if the installation has been
ATTENTION
de-energized!
Note:
When replacing cables, note the instructions of the machine
manufacturer.
If you do not use standard cables from Rexroth, then check to
ensure that the cables agree with the terminal diagram of the
machine manufacturer!
Rexroth IndraDrive
DOK-INDRV*-GEN-**VRS**-WA01-EN-P
- Quick Links:
- Coded Diagnostic Drive Messages
- Error
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the Rexroth IndraDrive and is the answer not in the manual?
Questions and answers
Our machine in Rexroth drive installation total 20 nos machine so facing issue shortly 5 drive folty 8060 erro so how to do
Error 8060 on Bosch Rexroth IndraDrive indicates an overcurrent in the power section. To resolve this issue for five machines, follow these steps for each machine:
1. Check the Load and Connections – Verify that the motor and power connections are correct and not causing excessive current draw.
2. Inspect the Power Section – Look for any visible damage or overheating signs in the power section.
3. Restart the System – Power off the drive, wait for the DC bus to discharge below 50V, and restart.
4. Adjust Parameters if Needed – Ensure that the drive’s current limits and motor settings are correctly configured.
5. Replace Faulty Components – If the issue persists, the power section may be defective and require replacement.
Repeat these steps for all five machines to ensure proper operation.
This answer is automatically generated
What is solution of 2110 fault in rexroth drive
The solution for the F2110 fault in Bosch Rexroth IndraDrive is:
1. If the failure occurs sporadically (firmware error), clear the error and contact the service department for a firmware update.
2. If the error occurs repeatedly, it indicates defective hardware. In this case, the control section or the entire device must be replaced.
3. Only Rexroth service engineers or specially trained users are allowed to replace the control section.
4. The procedure for replacing the entire drive controller is described in the Project Planning Manual for the power section.
This answer is automatically generated
The engine moves in manual mode but does not work in automatic mode. The error code is E2074. What should I do?
Error code F2074 indicates a defective motor encoder. To resolve this issue:
1. Check the position data reference – If the position data reference is incorrect, the encoder is defective.
2. Replace the motor or motor encoder – A faulty encoder can prevent movement in automatic mode.
3. Send the motor to the manufacturer’s service department for inspection.
If the issue persists, consult the service department for further assistance.
This answer is automatically generated
@Aleksand C0209incorrect encoder configuration error on drive controller display, red light fickering on drive comms port,
Please help me with the problem of the VM F2802 and E2810 errors on the Rexroth Indradrive M
The VM F2802 error on the Bosch Rexroth IndraDrive M indicates that the Phase-Locked Loop (PLL) is not synchronized.
The E2810 error means that the drive system is not ready for operation. This occurs when one or more drives in a system (connected via DC bus and module bus) signal an error, preventing the supply from being ready for power output. To resolve it, identify the drives signaling an error and remove the cause, or ensure all drives are in communication phase 4.
This answer is automatically generated
Medodyjsjddidi