Status Classes, Status Displays, Control Parameters - Bosch Rexroth IndraDrive Troubleshooting Manual
Hide thumbs
Also See for Rexroth IndraDrive:
- Applications manual (100 pages) ,
- Project planning manual (128 pages) ,
- Instruction manual (26 pages)
Table of Contents
Advertisement
1-4
Basics on Device Diagnosis
Status Classes, Status Displays, Control Parameters
Features
LSA Control S.L. www.lsa-control.com comercial@lsa-control.com (+34) 960 62 43 01
message number parameter and is a language-independent possibility of
determining and displaying the drive status on an operator interface.
Error Number
The error number contains only the error number without the diagnostic
text. It can be read with the P-0-0009, Error number parameter and is a
language-independent possibility of determining and displaying an error
condition on an operator interface. This parameter only contains a value
unequal zero when an error is present in the drive.
The error number is generated from the lowest 4 digits of the diagnostic
message number. For example, the F2028 Excessive deviation error
with the diagnostic message number "(0x)F2028" would produce the error
number "2028."
List of Diagnostic Numbers
The last 50 diagnostic message numbers displayed are stored in
chronological order in the S-0-0375, List of diagnostic numbers
parameter. Every change in the content of S-0-0390, Diagnostic
message number means that the old content is transferred to S-0-0375.
When reading S-0-0375 the last transferred diagnostic message number
appears in the first element of the parameter, the diagnostic message
number transferred before from S-0-0390 in the second element etc.
Language Selection
Via parameter S-0-0265, Language selection it is possible to define or
switch the language of diagnostic message texts.
In the drive there are many parameters with important status information
(bit lists). Some of the bits contained in these lists can be used for
configuring real-time status bits and additionally can be assigned to digital
outputs or to the configurable signal status word.
See "Digital Inputs/Outputs" in chapter "Extended Drive Functions" and
"Configurable Signal Status Word" in chapter "Master Communication"
Status Classes
Brief Description
The drive differentiates between 3 states (error, warning and message)
for which there is status information. To make the status information
available there are so-called status class parameters (S-0-0011,
S-0-0012, S-0-0013) that contain the respective status bits.
In addition to these status class parameters there are change bits
contained in the status word of the field bus (e.g. S-0-0135 in the case of
SERCOS) that display changes in one of the above-mentioned status
class parameters (collective information).
• status class parameter for errors (cf. S-0-0011)
• status class parameter for warnings (cf. S-0-0012)
• status class parameter for messages (cf. S-0-0013)
• change bits in status word of master communication (e.g. S-0-0135
in the case of SERCOS)
• change bits of class 2 and 3 diagnostics (S-0-0097 and S-0-0098)
can be masked in status word of master communication (e.g.
S-0-0135 in the case of SERCOS) to suppress individual bits or status
messages
Rexroth IndraDrive
DOK-INDRV*-GEN-**VRS**-WA01-EN-P
- Quick Links:
- Coded Diagnostic Drive Messages
- Error
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the Rexroth IndraDrive and is the answer not in the manual?
Questions and answers
Our machine in Rexroth drive installation total 20 nos machine so facing issue shortly 5 drive folty 8060 erro so how to do
Error 8060 on Bosch Rexroth IndraDrive indicates an overcurrent in the power section. To resolve this issue for five machines, follow these steps for each machine:
1. Check the Load and Connections – Verify that the motor and power connections are correct and not causing excessive current draw.
2. Inspect the Power Section – Look for any visible damage or overheating signs in the power section.
3. Restart the System – Power off the drive, wait for the DC bus to discharge below 50V, and restart.
4. Adjust Parameters if Needed – Ensure that the drive’s current limits and motor settings are correctly configured.
5. Replace Faulty Components – If the issue persists, the power section may be defective and require replacement.
Repeat these steps for all five machines to ensure proper operation.
This answer is automatically generated
What is solution of 2110 fault in rexroth drive
The solution for the F2110 fault in Bosch Rexroth IndraDrive is:
1. If the failure occurs sporadically (firmware error), clear the error and contact the service department for a firmware update.
2. If the error occurs repeatedly, it indicates defective hardware. In this case, the control section or the entire device must be replaced.
3. Only Rexroth service engineers or specially trained users are allowed to replace the control section.
4. The procedure for replacing the entire drive controller is described in the Project Planning Manual for the power section.
This answer is automatically generated
The engine moves in manual mode but does not work in automatic mode. The error code is E2074. What should I do?
Error code F2074 indicates a defective motor encoder. To resolve this issue:
1. Check the position data reference – If the position data reference is incorrect, the encoder is defective.
2. Replace the motor or motor encoder – A faulty encoder can prevent movement in automatic mode.
3. Send the motor to the manufacturer’s service department for inspection.
If the issue persists, consult the service department for further assistance.
This answer is automatically generated
@Aleksand C0209incorrect encoder configuration error on drive controller display, red light fickering on drive comms port,
Please help me with the problem of the VM F2802 and E2810 errors on the Rexroth Indradrive M
The VM F2802 error on the Bosch Rexroth IndraDrive M indicates that the Phase-Locked Loop (PLL) is not synchronized.
The E2810 error means that the drive system is not ready for operation. This occurs when one or more drives in a system (connected via DC bus and module bus) signal an error, preventing the supply from being ready for power output. To resolve it, identify the drives signaling an error and remove the cause, or ensure all drives are in communication phase 4.
This answer is automatically generated