Warnings - Bosch Rexroth IndraDrive Troubleshooting Manual
Hide thumbs
Also See for Rexroth IndraDrive:
- Applications manual (100 pages) ,
- Project planning manual (128 pages) ,
- Instruction manual (26 pages)
Table of Contents
Advertisement
Rexroth IndraDrive
Clearing Errors
Booting and Firmware Download
Warnings
DOK-INDRV*-GEN-**VRS**-WA01-EN-P
LSA Control S.L. www.lsa-control.com comercial@lsa-control.com (+34) 960 62 43 01
Diagnostic
Error class
message
number
F2xxx
non-fatal error
F3xxx
non-fatal safety
technology
error
F4xxx
interface error
F6xxx
travel range
error
F7xxx
safety
technology
error
F8xxx
fatal error
F9xxx and
fatal system
E-xxxx
error
Fig. 1-15:
Error classes and drive reaction
Errors are not automatically cleared; they have to be cleared by:
• the control unit by activating the S-0-0099, C0500 Reset class 1
diagnostics command or
• by the user via the control panel
Note:
Some errors can only be cleared in communication phase 2.
If the error status persists the drive controller generates the error
message again.
Errors
Note:
Apart from the mentioned error classes that can occur during
operation, errors can occur when the devices are booted and
during firmware download. These errors are not displayed at
the control panel with a diagnostic message number of the
"Fxxxx" pattern, but with a short text. Booting and firmware
download errors are described separately.
While in operation the drive controller carries out monitoring functions.
Some monitoring functions depend on the operating mode that is used
and/or parameter settings. If a status is detected that still allows correct
operation but persists, which would then cause an error to be generated,
a warning is generated.
Note:
Some warnings won't result in an error if they are ignored.
Basics on Device Diagnosis
Drive reaction
as set in P-0-0119, Best possible
deceleration
as set in P-0-0119, Best possible
deceleration
as set in P-0-0119, Best possible
deceleration
speed command value reset
Closed Loop: speed command value reset
Open Loop: deceleration under compliance
with P-0-0569, Maximum stator frequency
change
torque disable
torque disable
1-17
- Quick Links:
- Coded Diagnostic Drive Messages
- Error
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the Rexroth IndraDrive and is the answer not in the manual?
Questions and answers
Our machine in Rexroth drive installation total 20 nos machine so facing issue shortly 5 drive folty 8060 erro so how to do
Error 8060 on Bosch Rexroth IndraDrive indicates an overcurrent in the power section. To resolve this issue for five machines, follow these steps for each machine:
1. Check the Load and Connections – Verify that the motor and power connections are correct and not causing excessive current draw.
2. Inspect the Power Section – Look for any visible damage or overheating signs in the power section.
3. Restart the System – Power off the drive, wait for the DC bus to discharge below 50V, and restart.
4. Adjust Parameters if Needed – Ensure that the drive’s current limits and motor settings are correctly configured.
5. Replace Faulty Components – If the issue persists, the power section may be defective and require replacement.
Repeat these steps for all five machines to ensure proper operation.
This answer is automatically generated
What is solution of 2110 fault in rexroth drive
The solution for the F2110 fault in Bosch Rexroth IndraDrive is:
1. If the failure occurs sporadically (firmware error), clear the error and contact the service department for a firmware update.
2. If the error occurs repeatedly, it indicates defective hardware. In this case, the control section or the entire device must be replaced.
3. Only Rexroth service engineers or specially trained users are allowed to replace the control section.
4. The procedure for replacing the entire drive controller is described in the Project Planning Manual for the power section.
This answer is automatically generated
The engine moves in manual mode but does not work in automatic mode. The error code is E2074. What should I do?
Error code F2074 indicates a defective motor encoder. To resolve this issue:
1. Check the position data reference – If the position data reference is incorrect, the encoder is defective.
2. Replace the motor or motor encoder – A faulty encoder can prevent movement in automatic mode.
3. Send the motor to the manufacturer’s service department for inspection.
If the issue persists, consult the service department for further assistance.
This answer is automatically generated
@Aleksand C0209incorrect encoder configuration error on drive controller display, red light fickering on drive comms port,
Please help me with the problem of the VM F2802 and E2810 errors on the Rexroth Indradrive M
The VM F2802 error on the Bosch Rexroth IndraDrive M indicates that the Phase-Locked Loop (PLL) is not synchronized.
The E2810 error means that the drive system is not ready for operation. This occurs when one or more drives in a system (connected via DC bus and module bus) signal an error, preventing the supply from being ready for power output. To resolve it, identify the drives signaling an error and remove the cause, or ensure all drives are in communication phase 4.
This answer is automatically generated
Medodyjsjddidi