Danfoss VLT AutomationDrive FC 301 Programming Manual page 325

Parameter Lists
1-40 Back EMF at 1000 RPM
1-41 Motor Angle Offset
1-44 d-axis Inductance Sat. (LdSat)
1-45 q-axis Inductance Sat. (LqSat)
1-46 Position Detection Gain
1-47 Torque Calibration
1-48 d-axis Inductance Sat. Point
1-49 q-axis Inductance Sat. Point
1-5* Load Indep. Setting
1-50 Motor Magnetisation at Zero Speed
1-51 Min Speed Normal Magnetising [RPM]
1-52 Min Speed Normal Magnetising [Hz]
1-53 Model Shift Frequency
1-54 Voltage reduction in fieldweakening
1-55 U/f Characteristic - U
1-56 U/f Characteristic - F
1-57 Torque Estimation Time Constant
1-58 Flying Start Test Pulses Current
1-59 Flying Start Test Pulses Frequency
1-6* Load Depen. Setting
1-60 Low Speed Load Compensation
1-61 High Speed Load Compensation
1-62 Slip Compensation
1-63 Slip Compensation Time Constant
1-64 Resonance Damping
1-65 Resonance Damping Time Constant
1-66 Min. Current at Low Speed
1-67 Load Type
1-68 Motor Inertia
1-69 System Inertia
1-7* Start Adjustments
1-70 Start Mode
1-71 Start Delay
1-72 Start Function
1-73 Flying Start
1-74 Start Speed [RPM]
1-75 Start Speed [Hz]
1-76 Start Current
1-8* Stop Adjustments
1-80 Function at Stop
1-81 Min Speed for Function at Stop [RPM]
1-82 Min Speed for Function at Stop [Hz]
1-83 Precise Stop Function
1-84 Precise Stop Counter Value
1-85 Precise Stop Speed Compensation Delay
1-9* Motor Temperature
1-90 Motor Thermal Protection
1-91 Motor External Fan
1-93 Thermistor Resource
1-94 ATEX ETR cur.lim. speed reduction
1-95 Thermistor Sensor Type
1-96 Thermistor Sensor Resource
1-97 Thermistor Threshold level
1-98 ATEX ETR interpol. points freq.
1-99 ATEX ETR interpol points current
M0013101
Programming Guide
ExpressionLimit All set-ups
0 N/A All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
120 % All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
100 % All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
0 V All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
150 ms All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
100 % All set-ups
100 % All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
5 ms All set-ups
ExpressionLimit All set-ups
[0] Passive load All set-ups
0 kgm² All set-ups
ExpressionLimit All set-ups
[0] Rotor Detection All set-ups
0 s All set-ups
[2] Coast/delay time All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
0 A All set-ups
[0] Coast All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
[0] Precise ramp stop All set-ups
100000 N/A All set-ups
10 ms All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
[0] None All set-ups
0 % 2 set-ups
[0] KTY Sensor 1 All set-ups
[0] None All set-ups
80 °C 1 set-up
ExpressionLimit 1 set-up
ExpressionLimit 2 set-ups
Danfoss A/S © 10/2019 All rights reserved.
x FALSE 0
TRUE 0
x FALSE -6
x FALSE -6
TRUE 0
TRUE -
x TRUE 0
x FALSE 0
TRUE 0
TRUE 67
TRUE -1
x FALSE -1
FALSE 0
TRUE -1
TRUE -1
TRUE -3
FALSE 0
FALSE 0
TRUE 0
TRUE 0
TRUE 0
TRUE -2
TRUE 0
TRUE -3
x TRUE 0
x TRUE -
x FALSE -4
x FALSE -4
TRUE -
TRUE -1
TRUE -
FALSE -
TRUE 67
TRUE -1
TRUE -2
TRUE -
TRUE 67
TRUE -1
FALSE -
TRUE 0
TRUE -3
TRUE -
TRUE -
TRUE -
x TRUE -1
TRUE -
TRUE -
TRUE 100
x TRUE -1
x TRUE 0
Uint16
Int16
Int32
Int32
Uint16
Uint8
Int16
Uint16
Uint16
Uint16
Uint16 5 5
Uint16
Uint8
Uint16
Uint16
Uint16
Uint16
Uint16
Int16
Int16
Int16
Uint16
Uint16
Uint8
Uint32
Uint8
Uint32
Uint32
Uint8
Uint8
Uint8
Uint8
Uint16
Uint16
Uint32
Uint8
Uint16
Uint16
Uint8
Uint32
Uint8
Uint8
Uint8
Uint8
Uint16
Uint8
Uint8
Int16
Uint16
Uint16
323