Danfoss VLT AutomationDrive FC 301 Programming Manual page 204

Parameter Descriptions
13-01 Start Event
Select the boolean (true or false) input to activate smart logic
control.
Option:
[0] False
3 3
[1] True
[2] Running
[3] In range
[4] On reference
[5] Torque limit
[6] Current Limit
[7] Out of current
range
[8] Below I low
[9] Above I high
[10] Out of speed
range
[11] Below speed
low
[12] Above speed
high
[13] Out of feedb.
range
[14] Below feedb.
low
202
®
VLT AutomationDrive FC 301/302
Function:
Select the boolean (true or false)
input to activate smart logic
control.
Enters the fixed value - false.
Enters the fixed value - true.
The motor runs.
The motor runs within the
programmed current and speed
ranges set in
parameter 4-50 Warning Current Low
to parameter 4-53 Warning Speed
High.
The motor runs on reference.
The torque limit set in
parameter 4-16 Torque Limit Motor
Mode or parameter 4-17 Torque Limit
Generator Mode is exceeded.
The motor current limit set in
parameter 4-18 Current Limit is
exceeded.
The motor current is outside the
range set in parameter 4-18 Current
Limit.
The motor current is lower than set
in parameter 4-50 Warning Current
Low.
The motor current is higher than
set in parameter 4-51 Warning
Current High.
The speed is outside the range set
in parameter 4-52 Warning Speed
Low and parameter 4-53 Warning
Speed High.
The output speed is lower than the
setting in parameter 4-52 Warning
Speed Low.
The output speed is higher than
the setting in
parameter 4-53 Warning Speed High.
The feedback is outside the range
set in parameter 4-56 Warning
Feedback Low and
parameter 4-57 Warning Feedback
High.
The feedback is below the limit set
in parameter 4-56 Warning Feedback
Low.
Danfoss A/S © 10/2019 All rights reserved.
13-01 Start Event
Select the boolean (true or false) input to activate smart logic
control.
Option: Function:
[15] Above feedb. The feedback is above the limit set
high in parameter 4-57 Warning Feedback
High.
[16] Thermal The thermal warning turns on when
warning the temperature exceeds the limit
in the motor, the frequency
converter, the brake resistor, or the
thermistor.
[17] Mains out of The mains voltage is outside the
range specified voltage range.
[18] Reversing The output is high when the
frequency converter is running
counterclockwise (the logical
product of the status bits running
AND reverse).
[19] Warning A warning is active.
[20] Alarm (trip) A (trip) alarm is active.
[21] Alarm (trip A (trip lock) alarm is active.
lock)
[22] Comparator 0 Use the result of comparator 0.
[23] Comparator 1 Use the result of comparator 1.
[24] Comparator 2 Use the result of comparator 2.
[25] Comparator 3 Use the result of comparator 3.
[26] Logic rule 0 Use the result of logic rule 0.
[27] Logic rule 1 Use the result of logic rule 1.
[28] Logic rule 2 Use the result of logic rule 2.
[29] Logic rule 3 Use the result of logic rule 3.
[33] Digital input Use the result of digital input 18.
DI18
[34] Digital input Use the result of digital input 19.
DI19
[35] Digital input Use the result of digital input 27.
DI27
[36] Digital input Use the result of digital input 29.
DI29
[37] Digital input Use the result of digital input 32.
DI32
[38] Digital input Use the result of digital input 33.
DI33
[39] Start A start command is issued. This is
command the default option.
[40] Drive stopped A stop command (jog, stop, quick
stop, coast) is issued – and not
from the SLC itself.
[41] Reset Trip A reset is issued.
M0013101