Danfoss VLT AutomationDrive FC 301 Programming Manual page 209

Parameter Descriptions
13-10 Comparator Operand
Option: Function:
Mode or parameter 4-17 Torque Limit
Generator Mode.
[66] Current Limit The motor current exceeds the
value in parameter 4-18 Current
Limit.
[67] Out of current The motor current is outside the
range range set in parameter 4-18 Current
Limit.
[68] Below I low The motor current is lower than the
value in parameter 4-50 Warning
Current Low.
[69] Above I high The motor current is higher than
the value in parameter 4-51 Warning
Current High.
[70] Out of speed The speed is outside the range set
range in parameter 4-52 Warning Speed
Low and parameter 4-53 Warning
Speed High.
[71] Below speed The output speed is lower than the
value in parameter 4-52 Warning
low
Speed Low.
[72] Above speed The output speed is higher than
high the value in parameter 4-53 Warning
Speed High.
[75] Out of The feedback is outside the range
feedback set in parameter 4-56 Warning
range Feedback Low and
parameter 4-57 Warning Feedback
High.
[76] Below The feedback is lower than the limit
feedback low set in parameter 4-56 Warning
Feedback Low.
[77] Above The feedback exceeds the limit set
feedback high in parameter 4-57 Warning Feedback
High.
[80] Thermal This operand becomes true when
warning the frequency converter detects any
thermal warning, for instance when
the temperature exceeds the limit
in the motor, the frequency
converter, the brake resistor, or
thermistor.
[82] Mains out of The mains voltage is outside the
range specified voltage range.
[85] Warning If a warning is triggered, this
operand gets the warning number.
[86] Alarm (trip) A trip alarm is active.
[87] Alarm (trip A trip lock alarm is active.
lock)
M0013101
Programming Guide
13-10 Comparator Operand
Option:
[90]
[91]
[92]
[93]
[94]
[100]
[101]
[102]
[103]
[104]
[105]
[110]
[111]
[112]
[113]
[114]
[115]
[120]
[121]
[122]
[123]
[124]
[125]
[126]
[127]
[130]
[131]
[132]
[133]
[134]
[135]
[150]
Danfoss A/S © 10/2019 All rights reserved.
Function:
Bus OK Active communication (no timeout)
via the serial communication port.
Torque limit & If the frequency converter has
stop received a stop signal and is at the
torque limit, the signal is logic 0.
Brake fault The brake IGBT is short-circuited.
(IGBT)
Mech. brake The mechanical brake is active.
control
Safe stop
active
Comparator 0 The result of comparator 0.
Comparator 1 The result of comparator 1.
Comparator 2 The result of comparator 2.
Comparator 3 The result of comparator 3.
Comparator 4 The result of comparator 4.
Comparator 5 The result of comparator 5.
Logic rule 0 The result of logic rule 0.
Logic rule 1 The result of logic rule 1.
Logic rule 2 The result of logic rule 2.
Logic rule 3 The result of logic rule 3.
Logic rule 4 The result of logic rule 4.
Logic rule 5 The result of logic rule 5.
SL Time-out 0 The result of SLC timer 0.
SL Time-out 1 The result of SLC timer 1.
SL Time-out 2 The result of SLC timer 2.
SL Time-out 3 The result of SLC timer 3.
SL Time-out 4 The result of SLC timer 4.
SL Time-out 5 The result of SLC timer 5.
SL Time-out 6 The result of SLC timer 6.
SL Time-out 7 The result of SLC timer 7.
Digital input Digital input 18 (high=true).
DI18
Digital input Digital input 19 (high=true).
DI19
Digital input Digital input 27 (high=true).
DI27
Digital input Digital input 29 (high=true).
DI29
Digital input Digital input 32 (high=true).
DI32
Digital input Digital input 33 (high=true).
DI33
SL digital Use the result of the SLC output A.
output A
3 3
207