Xerox WorkCentre 7132 Service Documentation page 953

REP 16.9.1 Compiler Tray Assembly..............................................................................
REP 16.10.1 Stacker Motor Assembly ............................................................................
REP 16.10.2 Elevator Belt Assembly..............................................................................
REP 16.11.1 Paddle Gear Shaft .....................................................................................
REP 16.12.1 Finisher PWB.............................................................................................
REP 16.12.2 Finisher LVPS PWB...................................................................................
7. MPT
ADJ 7.1.1 MSI (Bypass) Tray Guide Adjustment ............................................................
9. Xerographics
ADJ 9.1.0 Toner Density Adjustment ..............................................................................
ADJ 9.1.1 IOT Image Registration ..................................................................................
ADJ 9.1.2 Max Setup ......................................................................................................
ADJ 9.1.6 TRC Adjustment .............................................................................................
ADJ 9.1.7 Color-To-Color Registration ...........................................................................
ADJ 9.1.8 IIT Calibration .................................................................................................
ADJ 9.1.9 Optical Axis Alignment ...................................................................................
ADJ 9.1.10 Procon ON/OFF Print ...................................................................................
ADJ 9.2.1 Edge Erase Value Adjustment .......................................................................
ADJ 9.3.1 Software Loading and Upgrading...................................................................
11. IIT
ADJ 11.1.1 IIT Lead Edge/Side Edge Registration .........................................................
ADJ 11.1.2 IIT Vertical/Horizontal Magnification.............................................................
ADJ 11.2.1 Reduce/Enlarge Adjustment.........................................................................
ADJ 11.3.1 UI Alignment.................................................................................................
ADJ 11.6.1 Full/Half Rate Carriage Position Adjustment ................................................
15. DADF
ADJ 15.1.1 DADF Side Edge Registration......................................................................
ADJ 15.1.3 DADF Non-Standard Sized Original Customized Registration Function......
ADJ 15.1.4 DADF Lead Edge Registration .....................................................................
ADJ 15.1.5 DADF Height Adjustment .............................................................................
ADJ 15.1.6 DADF Position (Skew) Adjustment...............................................................
22 a-finisher
REP 22.1 A-Finisher .......................................................................................................
REP 22.3.1 Paddle Belt ..................................................................................................
REP 22.3.2 Sub Paddle Solenoid ...................................................................................
REP 22.4.1 Exit Roll Assembly .......................................................................................
REP 22.4.2 Staple Assembly ..........................................................................................
REP 22.4.3 Set Clamp Home Sensor .............................................................................
REP 22.4.4 Exit Roll Assembly .......................................................................................
REP 22.5.1 Pinch Roll.....................................................................................................
REP 22.5.2 Finisher Entrance Sensor ............................................................................
REP 22.5.3 Compile Exit Sensor ....................................................................................
REP 22.5.4 Main Paddle Shaft Assembly .......................................................................
REP 22.5.5 Lower Chute Assembly ................................................................................
REP 22.6.1 ENT Roll Assembly......................................................................................
REP 22.6.2 Upper Chute Assembly ................................................................................
REP 22.7.1 Finisher Control PWB ..................................................................................
REP 22.8.1 Stacker Tray Assembly ................................................................................
Repairs/Adjustments
4-177 REP 22.8.2 Stacker Shaft Assembly...............................................................................
4-179 REP 22.8.3 Stacker Motor...............................................................................................
4-181 REP 22.8.4 Stacker Stack Sensor ..................................................................................
4-182 REP 22.9.1 Compile Assembly .......................................................................................
4-184 REP 22.9.2 Set Clamp Shaft...........................................................................................
4-185 REP 22.9.3 Eject Belt......................................................................................................
REP 22.9.4 Eject/Set Clamp Motor Assembly ................................................................
REP 22.9.5 Rear Tamper Home Sensor.........................................................................
4-193
REP 22.9.6 Eject Shaft Assembly ...................................................................................
REP 22.10.1 Front /Rear Tamper Motor Assembly.........................................................
REP 22.10.2 Front Tamper Home Sensor ......................................................................
4-195
REP 22.10.3 Eject Clamp Home Sensor.........................................................................
4-195
REP 22.10.4 Stack Height Sensor ..................................................................................
4-198
4-199
4-199
4-203
4-205
4-206
4-211
4-211
4-213
4-214
4-215
4-216
4-217
4-221
4-222
4-223
4-225
4-226
4-229
4-230
4-233
4-234
4-236
4-237
4-238
4-240
4-240
4-242
4-243
4-245
4-247
4-249
4-251
4-251
January 2007
4-2
4-253
4-255
4-257
4-257
4-259
4-261
4-262
4-264
4-266
4-267
4-269
4-270
4-271
Reversion 4.0
WorkCentre 7132