Xerox WorkCentre 7132 Service Documentation page 1415

Chain-Link NVM Name
700-120 Time Zone
700-124 Auto Clear Timer (Combining Auto
Resume Timer, Auditron Off Timer and
Tools Off Timer)
700-125 Job Cancel Timer
700-126 Operating Timer
700-127 Job End Timer
700-128 Scanning Timer
700-129 Low Power Mode Timer
700-130 Sleep Mode Timer
700-131 Sleep Mode Availability Setting
700-132 Operation Panel Normal Input Beep
700-133 Operation Panel Error Input Beep
700-134 Normal Completion Beep (Copy)
700-135 Normal Completion Beep (Other than
Copy)
700-136 Abnormal Warning Beep
700-137 Abnormal Completing Beep
700-138 Ready Beep
700-139 Toner Empty Warning Beep
700-140 Bell Tone
700-141 Line Monitor Tone
700-142 Low Power Mode Availability Setting
700-143 Job Memory Entry Tone
700-144 Job History Report Auto Output Specifica-
tion
700-145 Duplex Printing Specification
700-146 Mail Box Receive Notification Report Out-
put Specification
General procedures information
Controller & Fax NVM List
Table 1 Common
Setup Initial
Range Value Read/Write Description
-600~+600 : Read/Write Displays the time difference from GMT. For example, Japan: 540, Hawaii: -600
+540(FX
Default)
+600 (AP
default)
-300 (XC
default)
0~240 1min (MF: Read/Write Input from the menu is MF: 0 (Disable), 60, 120, 180, 240 (sec), P: 0 (Disable),
60, P: 1) 1~30 (min)
0 (prohibit)~240 can be entered from ChainLink for MF and P but they must be
within the range specified above.
0~5940 10min Read/Write 0, 240~5940: [Disable, 4~99min](1min increments) (The MF-UI SOD has a dif-
ferent value.)
0~240 10sec Read/Write 0: Not started, 1~240: [1~240sec](1sec increments)
0~240 6sec Read/Write 0: Not started, 1~240: [1~240sec](1sec increments)
1~20 4sec, 3sec Read/Write 1~20: [1~20sec (1sec increments)]
(Allagash
only)
1~240 15min Read/Write 1~240: [1~240min (1min increments)], (Ignored if Low Power mode is disabled)
1~240 60min Read/Write 1~240: [1~240min (1min increments)], (Ignored if Sleep Mode is disabled)
0~1 1: Enable Read/Write 0: Not valid, 1: Valid
0~3 2: Normal Read/Write 0: Off, 1: Soft, 2: Normal, 3: Loud
0~3 2: Normal Read/Write 0: Off, 1: Soft, 2: Normal, 3: Loud
0~3 2: Normal Read/Write 0: Off, 1: Soft, 2: Normal, 3: Loud
0~3 2: Normal Read/Write 0: Off, 1: Soft, 2: Normal, 3: Loud
0~3 0: Off Read/Write 0: Off, 1: Soft, 2: Normal, 3: Loud
(For P Models, there is no volume adjustment. Any setting in soft, normal or
loud means On.)
0~3 2: Normal Read/Write 0: Off, 1: Soft, 2: Normal, 3: Loud
0~3 2: Normal Read/Write 0: Off, 1: Soft, 2: Normal, 3: Loud
0~3 2: Normal Read/Write 0: Off, 1: Soft, 2: Normal, 3: Loud
0~3 2: Normal Read/Write 0: Off, 1: Soft, 2: Normal, 3: Loud
0~3 2: Normal Read/Write 1: Soft, 2: Normal, 3: Loud
0~1 1: Enable Read/Write 0: Disable, 1: Enable
0~3 2: Normal Read/Write 0: Off, 1: Soft, 2: Normal, 3: Loud
0~1 0: OFF Read/Write 0: OFF, 1: ON
0~1 0: OFF Read/Write 0: OFF, 1: ON
0~1 ON Read/Write 0: OFF, 1: ON
January 2007
6-92
Reversion 4.0
WorkCentre 7132