Xerox WorkCentre 7132 Service Documentation page 952

1. Drives
REP 1.1.1 Main Drive Assembly .....................................................................................
REP 1.1.2 Drum Drive Assembly ....................................................................................
2. Paper Transportation
REP 2.1.1 Tray 1 Feeder ................................................................................................
REP 2.3.1 Tray 1 Feed/Nudger/Retard Roll....................................................................
REP 2.4.1 Registration Unit ............................................................................................
REP 2.5.1 Takeaway Roll ...............................................................................................
REP 2.6.2 L/H Upper Cover Unit ....................................................................................
3. ROS
REP 3.1.1 ROS Unit........................................................................................................
4. Xerographics/Development
REP 4.1.1 Developer Housing ........................................................................................
REP 4.1.2 Toner Cartridge..............................................................................................
REP 4.1.3 Developer Bias Brush ....................................................................................
REP 4.1.4 Waste Toner Auger........................................................................................
REP 4.2.1 Developer Motor Assembly............................................................................
REP 4.2.2 IBT Module ....................................................................................................
REP 4.2.3 Print Drum......................................................................................................
REP 4.2.4 IBT Cleaner....................................................................................................
REP 4.2.5 IBT Belt ..........................................................................................................
REP 4.2.6 Rotary Drive Motor.........................................................................................
REP 4.2.7 Developer Material.........................................................................................
REP 4.2.8 2nd BTR Contact Arms..................................................................................
REP 4.3.1 Sensor Bar.....................................................................................................
5. Fuser
REP 5.1.1 Fuser Unit ......................................................................................................
6. Exit
REP 6.1.1 Exit2 + OCT2 .................................................................................................
7. MPT
REP 7.1.1 MSI Assembly................................................................................................
REP 7.2.1 MSI Feed Roll/Retard Pad.............................................................................
9. Electrical Components
REP 9.1.1 MCU PWB .....................................................................................................
REP 9.1.2 MCU PWB EPROM .......................................................................................
REP 9.2.1 ESS PWB ......................................................................................................
REP 9.2.2 ESS PWB EPROM ........................................................................................
REP 9.2.3 Power Supply PWB .......................................................................................
10. Covers
REP 10.1.1 Top Cover Assembly ...................................................................................
REP 10.2.1 Rear Lower Covers......................................................................................
REP 10.2.2 Front Inner Cover.........................................................................................
REP 10.2.3 Right Side Cover..........................................................................................
REP 10.3.1 Rear Fan......................................................................................................
11. IIT
Reversion 4.0
WorkCentre 7132
REP 11.1.1 Platen Cushion.............................................................................................
REP 11.1.2 Control Panel Assembly...............................................................................
4-3
REP 11.3.1 Platen Glass.................................................................................................
4-10
REP 11.3.2 IIT/IPS PWB.................................................................................................
REP 11.4.1 Lens Kit Assembly .......................................................................................
4-13
REP 11.5.1 Carriage Cable.............................................................................................
4-15
REP 11.5.2 Carriage Motor Assembly ............................................................................
4-17
REP 11.6.1 Exposure Lamp............................................................................................
4-18
REP 11.6.2 Lamp Wire Harness .....................................................................................
4-20
12. Tray Module - 2T
REP 12.1.1 Tray 2 Feeder (2TM)....................................................................................
4-21
REP 12.1.2 Tray 3 Feeder (2TM)....................................................................................
REP 12.3.1 Feed/Retard/Nudger Roll (2TM) ..................................................................
REP 12.6.1 2TM PWB.....................................................................................................
4-23
4-26
13. Tray Module - TT
4-27
REP 13.1.1 Tray 2 Assembly (TTM) ...............................................................................
4-28
REP 13.1.2 Tray 3 Assembly (TTM) ...............................................................................
4-30
REP 13.3.1 Front/Rear Tray Cable (TTM) ......................................................................
4-31
REP 13.4.1 Tray 3 Feeder (TTM)....................................................................................
4-35
REP 13.5.1 Tray 2 Feeder (TTM)....................................................................................
4-36
REP 13.6.1 Feed/Retard/Nudger Roll (TTM) ..................................................................
4-37
REP 13.8.1 TTM PWB ....................................................................................................
4-43
15. DADF
4-44
REP 15.1.1 DADF ...........................................................................................................
4-48
REP 15.1.2 DADF Platen Cushion..................................................................................
4-50
REP 15.2.1 DADF Document Tray..................................................................................
REP 15.2.2 DADF Feeder Assembly ..............................................................................
4-53
REP 15.2.3 DADF Front Cover .......................................................................................
REP 15.2.4 DADF Rear Cover........................................................................................
REP 15.3.1 DADF PWB ..................................................................................................
4-55
REP 15.3.2 Left Counter Balance ...................................................................................
REP 15.3.3 Right Counter Balance.................................................................................
REP 15.4.1 Retard Roll ...................................................................................................
4-57
REP 15.4.2 Top Cover Assembly....................................................................................
4-59
REP 15.6.1 Nudger Roll, Feed Roll.................................................................................
REP 15.8.1 Registration Roll...........................................................................................
4-61
16. Finisher
4-63
REP 16.1.1 H-Transport Assembly .................................................................................
4-64
REP 16.1.2 Finisher Assembly........................................................................................
4-69
REP 16.3.1 H-Transport Belt...........................................................................................
4-69
REP 16.4.1 Front Cover Assembly .................................................................................
REP 16.4.2 Rear Cover...................................................................................................
4-71
REP 16.5.1 Stack Height Sensor Assembly....................................................................
4-72
REP 16.5.2 Eject Roll Assembly .....................................................................................
4-74
REP 16.6.1 Decurler Roll ................................................................................................
4-75
REP 16.6.2 Finisher Drive Motor.....................................................................................
4-76
REP 16.7.1 Paper Eject Belt ...........................................................................................
REP 16.8.1 Staple Unit Rail ............................................................................................
REP 16.8.2 Staple Assembly ..........................................................................................
January 2007
4-1
4-77
4-78
4-78
4-79
4-84
4-86
4-92
4-96
4-97
4-101
4-104
4-107
4-108
4-111
4-112
4-113
4-114
4-117
4-119
4-120
4-123
4-125
4-126
4-128
4-130
4-130
4-132
4-133
4-134
4-135
4-137
4-142
4-147
4-151
4-151
4-155
4-157
4-158
4-159
4-160
4-166
4-168
4-168
4-171
4-176
Repairs/Adjustments