Xerox WorkCentre 7132 Service Documentation page 1348

Chain-Link Name
742-273 Timing of Finishing Countermeasure Ope against Con-
densation (full speed)
742-274 Timing of Finishing Countermeasure Ope against Con-
densation (half speed)
742-281 MSI-Feed Paper Qty
742-282 Tray 1- Feed Paper Qty
742-283 Tray 2-Feed Paper Qty
742-284 Tray 3-Feed Paper Qty
742-285 Qty of Tray 1 Lifter Adjustments
742-286 Tray 1 Lift Up Time
742-287 Tray 2 Lift Up Time
742-288 Tray 3 Lift Up Time
742-289 Count Coefficient for Remaining Paper Qty Detection
(Tray 1)
(Remaining Qty Correction Time in adjusting Lifter)
742-290 Count Coefficient for Remaining Paper Qty Detection
(2TM-Tray 2)
(Remaining Qty Correction Time in adjusting Lifter)
742-291 Count Coefficient for Remaining Paper Qty Detection
(2TM-Tray 3)
(Remaining Qty Correction Time in adjusting Lifter)
742-292 Count Coefficient for Remaining Paper Qty Detection
(TTM-Tray 2)
(Remaining Qty Correction Time in adjusting Lifter)
742-293 Count Coefficient for Remaining Paper Qty Detection
(TTM-Tray 3)
(Remaining Qty Correction Time in adjusting Lifter)
742-294 MSI Size Guide minimum position
742-295 MSI Size Guide maximum position
742-301 OHP Sensor PWM default value (at Power On)
742-302 OHP Sensor Correction Operation standard value
742-303 OHP Sensor target value
742-304 Sampling Qty (in OHP correction operation)
742-305 Sampling Qty (detection of paper type)
742-306 Delay in sampling (in OHP correction operation)
Reversion 4.0
WorkCentre 7132
Table 3 Paper Handling
Step Read/
Default Range (mm) Write
14 0~50 100ms RW
27 0~50 100ms RW
0 0~1500000 R
0 0~1500000 R
0 0~600000 R
0 0~600000 R
0 0~100 R
0 0~3000 R
0 0~15000 R
0 0~15000 R
30 0~100 1ms RW
30 0~100 1ms RW
30 0~100 1ms RW
34 0~100 1ms RW
34 0~100 1ms RW
963 904~1023 RW
194 0~258 RW
1000 0~1000 0.1% RW
1000 0~1000 0.1% RW
155 60~330 1 RW
2 1~5 2 RW
10 1~20 1 RW
3 1~10 1ms RW
January 2007
6-25
Description
Timing of stopping Exit 2 Motor after Exit Sensor 1Off (full speed)
Timing of stopping Exit 2 Motor after Exit Sensor 1Off (half speed)
It is time to replace the periodic replacement part: TA Roll
It is time to replace the periodic replacement part: TA Roll
It is time to replace periodic replacement parts:
Nudger/Feed/Retard Roll
It is time to replace periodic replacement parts:
Nudger/Feed/Retard Roll
Counts Tray 1 Lifter adjustments. Every time Lifter is adjusted after it lifts up, 1
is added. (for reference)
Stores Tray 1 Lift Up time. (for reference)
Stores Tray 2 Lift Up time. (for reference)
Stores Tray 3 Lift Up time. (for reference)
Coefficient for detecting and calculating what quantity of paper remains in Tray
1. (time taken to adjust Lifter)
Coefficient for detecting and calculating what quantity of paper remains in 500-
sheet Tray. (time taken to adjust Lifter)
Coefficient for detecting and calculating what quantity of paper remains in 500-
sheet Tray. (time taken to adjust Lifter)
Coefficient for detecting and calculating what quantity of paper remains in TTM
Tray 2. (time taken to adjust Lifter)
Coefficient for detecting and calculating what quantity of paper remains in TTM
Tray 3. (time taken to adjust Lifter)
Stores min. data in correcting Size Sensor.
Stores max. data in correcting Size Sensor.
Default to execute auxiliary operation that controls variations in OHP Sensor.
(used with Power On)
Default to execute auxiliary operation that controls variations in OHP Sensor
Adjusts threshold to correct OHP PWM output value in OHP correction opera-
tion.
Adjusts how many samples of OHP Sensor Value to take in OHP correction
operation.
Adjusts how many samples of OHP Sensor Value to take in detecting paper
type.
Adjusts how long to delay sampling OHP Sensor value after PWM output in
OHP correction operation.
General procedures information
IOT NVM List