Xerox WorkCentre 7132 Service Documentation page 1404

Chain-Link Content
715-022 Lamp Fan Fail Bypass
715-023 Lamp Fan On Time (Low Rotation)
715-024 Lamp Fan Off Time
715-025 FL Timer Set
715-026 Lamp ON Interval
715-027 Lamp ON Time
715-030 IIT Failure Part Diagnosis
715-050 Platen SS Registration Adjustment
715-051 Platen SS Reduce/Enlarge Adjustment
715-052 Platen Glass Type
715-053 Platen PRadjF
715-056 CVT FS Offset Side1-1 (139.7-148)
715-057 CVT FS Offset Rear Side2-1 (139.7~148)
715-058 CVT FS Offset Side1-2 (182-194)
715-059 CVT FS Offset Side2-2 (182-194)
715-060 CVT FS Offset Side1-3 (203.2)
715-061 CVT FS Offset Side2-3 (203.2)
715-062 CVT FS Offset Side1-4 (210)
715-063 CVT FS Offset Side2-4 (210)
715-064 CVT FS Offset Side1-5 (214.9-215.9)
715-065 CVT FS Offset Side2-5 (214.9-215.9)
715-066 CVT FS Offset Side1-6 (254-257)
715-067 CVT FS Offset Side2-6 (254-257)
715-068 CVT FS Offset Side1-7 (266.7-267)
715-069 CVT FS Offset Side2-7 (266.7-267)
715-070 CVT FS Offset Side1-8 (279.4)
715-071 CVT FS Offset Side2-8 (279.4)
715-072 CVT FS Offset Side1-9 (297)
715-073 CVT FS Offset Side2-9 (297)
715-074 CVT FS Offset Side3-1 (139.7-148)
715-075 CVT FS Offset Side4-1 (139.7-148)
715-076 CVT FS Offset Side3-2 (182-194)
Reversion 4.0
WorkCentre 7132
Table 3 IISS
Default Range Meaning
1 0~1 Existence or of Lamp Fan Fail Detection
0: Lamp Fan Fail Detection existent
1: Lamp Fan Fail Detection not existent
15 0~60 Lamp Fan On at Low Speed time (in minute)
1 0~60 Lamp Fan Off time (in minute)
0 0~1 0: Standard FL Timer settings (30min rest/0.5sec On), 1: Condensation mode setting (Diag 715-
026, 715-027 timer settings apply)
30 0~60 Interval setting (unit: min)
1 0~60 Lamp ON time setting (unit: sec)
1 0~65535 Writing 1 allows starting diagnostics of a failed IIT part.
Reading this NVM after diagnostics is made on a failed part makes a certain presumed part No.
appear.
If a fail occurs during diagnostics of a failed part, Fail Code associated with the fail is logged in this
NVM and the diagnostics ends.
*Even if 1 is written, 1 is not actually done.
*If any value other than 1 is entered, the value becomes illegal.
100 16~184 Slow Scan Direction Regi Correction Value (0.036mm/increment), Factory Settings
50 44~56 Slow Scan Direction Regi Correction Value (0.1%/increment), Factory Settings
2 0~2 0: Platen model, 1: Belt DADF, 2: CVT, Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (Dot), VLSS=PROMVLSS+(PRadjF-120)x2, Factory Set-
tings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (0.1mm/increment) in CVT. Factory Settings
January 2007
6-81
General procedures information
IIT NVM List