Siemens SINUMERIK 808D ADVANCED Diagnostic Manual page 75

4340 [Channel %1: ] Block %2 invalid transformation type in transformation no. %3
Parameters: %1 = Channel number
%2 = Block number, label
%3 = Transformation number
Definitions: An invalid, i.e. undefined number was entered in one of the machine data $MC_TRAFO_TYPE_.... This alarm also
occurs if a certain type of transformation is only impossible on the type of control used (e.g. a 5-axis transformation).
Reaction: Correction block is reorganized.
Interface signals are set.
Alarm display.
NC Stop on alarm at block end.
Remedy: Enter a valid transformation type.
Program Clear alarm with the RESET key. Restart part program
Continuation:
4341 [Channel %1: ] Block %2 no data set available for transformation no. %3
Parameters: %1 = Channel number
%2 = Block number, label
%3 = Transformation number
Definitions: Only a limited number of machine data sets (usually 2) is available for each related group of transformations (e.g.
orientation transformations, Transmit, Tracyl, etc.). This alarm is output if an attempt is made to set more
transformations from a group.
Example:
Two orientation transformations are allowed. The machine data contains e.g.:
TRAFO_TYPE_1 = 16 ; 1st orientation transformation
TRAFO_TYPE_2 = 33 ; 2nd orientation transformation
TRAFO_TYPE_3 = 256 ; 1st transmit transformation
TRAFO_TYPE_4 = 20 ; 3rd orientation transformation ==> This entry triggers alarm
Reaction: Correction block is reorganized.
Interface signals are set.
Alarm display.
NC Stop on alarm at block end.
Remedy: Enter valid machine data.
Program Clear alarm with the RESET key. Restart part program
Continuation:
4342 [Channel %1: ] Invalid machine data for general 5-axis transformation error no. %2
Parameters: %1 = Channel number
%2 = Error type
Definitions: The machine data which describe the axis directions and the basic orientation and the input axes for the general 5-
axis transformation are invalid. The error parameter displayed specifies the cause of the alarm:
- 1: The first axis (MD2.... $MC_TRAFO5_AXIS1_...) is not defined (all three entries of the vector are 0)
- 2: The second axis (MD2.... $MC_TRAFO5_AXIS2_...) is not defined (all three entries of the vector are 0)
- 3: The basic orientation (MD2.... $MC_TRAFO5_BASE_ORIENT_...) is not defined (all three entries of the vector are
0)
- 4: The first and second axis are (virtually) parallel
- 5: On MD2.... $MC_TRAFO_TYPE_ = 56 (rotatable tool and workpiece) there is no 4-axis transformation, i.e. 2 rotary
axes must always be available. (See MD2.... $MC_TRAFO_AXES_IN_...)
- 6: The third axis (MD2.... TRAFO5$MC_TRAFO5_AXIS3_...) is not defined (all three entries of the vector are 0) (6-
axis transformation)
- 7: The normal tool vector (MD2.... TRAFO6$MC_TRAFO6_BASE_ORIENT_NORMAL_...) is not defined (all three
entries of the vector are 0) (6-axis transformation)
- 8: The basic tool orientation (MD2.... $MC_TRAFO5_BASE_ORIENT_...) and the normal tool vector (MD2....
$MC_TRAFO6_BASE_ORIENT_NORMAL_...) are (virtually) parallel (6-axis transformation)
- 9: The first external axis (MD2.... $MC_TRAFO7_EXT_AXIS1_*) has not been defined (all three vector entries are
0) (7-axis transformation)
-10: Invalid transformation type (MD2.... $MC_TRAFO_TYPE_...). A transformation type unequal to 24 has been
entered for the generic 7-axis transformation.
Diagnostics Manual
Diagnostics Manual, 08/2013, 6FC5398-6DP10-0BA1
SINUMERIK 808D ADVANCED alarms
3.2 NCK alarms
75