Siemens SINUMERIK 808D ADVANCED Diagnostic Manual page 400

SINUMERIK 808D ADVANCED alarms
3.5 Cycle alarms
4. Error code = D -> Rotary axis 1 not rotated for the 2nd or 3rd measurement with reference to the 1st measurement-
> see parameter_OVR[60 to 62]
61430 [Channel %1: ] Block %2: Kinematic vectors not computed - Error code: %4
Parameters: %1 = Channel number
%2 = Block number, label channel number
Definitions:
Remedy: Causes of error:
1. Error code = A -> Plausibility of the input points PM1, PM2, PM3 not fulfilled, resulting side lengths must not be
equal to zero
able to form a triangle, check => PM1...3.)
2. Error code = B
3. Error code = C
4. Error code = D
5. Error code = E
6. Error code = F
7. Error code = G -> If the computed angle is larger than the limiting value of the angular segment of the rotary axis
inaccuracies
8. Error code = "CC Option? " -> Option compile cycle "Measurement of kinematics" not set
9. Error code = "$MN_CC_ACTIVE_IN_CHAN_C996[0] ? " -> machine data for compile cycle not set
10. Error code = "License? " -> License for "Measurement of kinematics" not set
61440 [Channel %1: ] Block %2: Position of cutting edge cannot be determined
Parameters: %1 = Channel number
%2 = Block number, label channel number
Definitions:
Remedy: A turning tool with a cutting edge position between 1 and 8 must be used as the tool type.
Check the entered cutting edge position with reference to the basic position of the tool carrier.
61441 [Channel %1: ] Block %2: Position of cutting edge is not in the machining plane.
Parameters: %1 = Channel number
%2 = Block number, label channel number
Definitions:
Remedy: The position of the cutting edge of the turning tool (cutting tip) is no longer in the machining plane (interpolation plane),
this can be caused, for example, by a tool carrier with orientation capability. Correct the tool carrier position.
61442 [Channel %1: ] Block %2: Tool carrier not parallel to the geometry axes
Parameters: %1 = Channel number
%2 = Block number, label channel number
Definitions:
Remedy: After positioning the orientable tool carrier, tool lengths L1, L2 and L3 are not parallel to the geometry axes.
Check the positioning behavior of the rotary axes (blocking) of the tool carrier.
61443 [Channel %1: ] Block %2: Advance angle %4 or greater/less than +/-90° or +/-120°
Parameters: %1 = Channel number
%2 = Block number, label channel number
400
(Notice: even in the case of side lengths not equal to zero, there is a risk of not being
-> Enclosed angle at PM1 between the spread vectors PM1PM2 and PM1PM3 is equal to 0.
Starting points do not form a triangle.
-> Enclosed angle at PM2 between the spread vectors PM2PM1 and PM2PM3 is equal to 0.
Starting points do not form a triangle.
-> Enclosed angle at PM3 between the spread vectors PM3PM1 and PM3PM2 is equal to 0.
Starting points do not form a triangle.
-> Normalizing interpolation point: Invalid axis name defined for computation
-> Normalizing interpolation point: Invalid plane defined for computation
in parameter _TNVL. The computed limit angle and the name of the rotary axis are displayed.
With values of _TNVL < 20 degrees, inaccuracies are to be expected as a result of measuring
in the micrometer range of the probe.
Example display: "G Axis:C->TVLmin=12.345"
Remedy: Adjust angular value of rotary axis in user program or parameter _TNVL.
Diagnostics Manual, 08/2013, 6FC5398-6DP10-0BA1
Diagnostics Manual