Jeep 1987 Wrangler Workshop Manual page 1418

GENERAL DESCRIPTION
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS
Component Service Set-To Torque Service Recheck Torque
Air Injection Tube-to-Manifold
27 N-m (20 ft-lbs)
20-27 N-m (15-20 ft-lbs)
Air Pump-to-Bracket
27 N-m (20 ft-lbs)
20-30 N-m (15-22 ft-lbs)
Air Pump Brackets-to-Engine (A.C.
Compressor or Pedestals)
34 N-m (25 ft-lbs)
24-38 N-m (18-28 ft-lbs)
Air Pump Adjusting Strap-to-Pump
27 N-m (20 ft-lbs)
20-30 N-m (15-22 ft-lbs)
Alternator Pivot Bolt or Nut
38 N-m (28 ft-lbs)
27-47 N-m (20-35 ft-lbs)
Alternator Adjusting Bolt 24 N-m (18 ft-lbs)
20-27 N-m (15-20 ft-lbs)
Alternator Mounting Bracket-
to-Engine
38 N-m (28 ft-lbs)
31-41 N-m (23-30 ft-lbs)
Alternator Pivot Mounting Bolt-
to-Head
45 N-m (33 ft-lbs)
41-47 N-m (30-35 ft-lbs)
Block Heater Nut 2 N-m (20 in-lbs)
2-3 N-m (17-25 in-lbs)
Camshaft Sprocket Screw
68 N-m (50 ft-lbs)
61-75 N-m (45-55 ft-lbs)
Carburetor Hold-Down Nuts 19 N-m (14 ft-lbs)
16-27 N-m (12-20 ft-lbs)
Coil Bracket-to-Cylinder Head Bolt
19 N-m (14 ft-lbs)
14-24 N-m (10-18 ft-lbs)
Connecting Rod Bolt Nuts
45 N-m (33 ft-lbs)
41-47 N-m (30-35 ft-lbs)
Cylinder Head Capscrews
115 N-m (85 ft-lbs)
108-122 N-m (80-90 ft-lbs)
Cylinder Head Cover Nuts
3.2 N-m (28 in-lbs)
2.8-3.5 N-m (25-31 in-lbs)
Crankshaft Pulley-to-Damper
27 N-m (20 ft-lbs)
20-34 N-m (15-25 ft-lbs)
Clutch Housing Spacer-to-
Block Screws
16 N-m (12 ft-lbs)
12-20 N-m (9-15 ft-lbs)
Clutch Housing-to-Block
Screws (top)
37 N-m (27 ft-lbs)
30-41 N-m (22-30 ft-lbs)
Clutch Housing-to-Block
Screws (bottom)
58 N-m (43 ft-lbs)
50-64 N-m (37-47 ft-lbs)
Differential Housing-to-Left Engine
Mounting Bolt
54 N-m (40 ft-lbs)
47-68 N-m (35-50 ft-lbs)
Distributor Clamp Bracket Screw
18 N-m (13 ft-lbs)
14-24 N-m (10-18 ft-lbs)
Drive Plate-to-Converter Bolt
30 N-m (22 ft-lbs)
27-34 N-m (20-25 ft-lbs)
12