SATO CL4NX Programming Reference Manual page 530

Name of Setting item
BUZZER "0": Buzzer off
"1": Volume low
"2": Volume medium
"3": Volume large
BUZZER_POWERO "0": Buzzer off
FF "1": Volume low
"2": Volume medium
"3": Volume large
LCDVOLUME "0" to "9"
ADJUSTPITCH [CL4NX]
609dpi:"-90" to "90" (dot)
305dpi:"-45" to "45" (dot)
203dpi:"-30" to "30" (dot)
[CL6NX]
305dpi:"-45" to "45" (dot)
203dpi:"-30" to "30" (dot)
ADJUSTOFFSET [CL4NX]
609dpi:"-90" to "90" (dot)
305dpi:"-45" to "45" (dot)
203dpi:"-30" to "30" (dot)
[CL6NX]
305dpi:"-45" to "45" (dot)
203dpi:"-30" to "30" (dot)
ADJ_PITCHOFFSE [CL4NX]
T 609dpi:"-1176" to "1176"(dot)
305dpi:"-588" to "588"(dot)
203dpi:"-392" to "392"(dot)
[CL6NX]
305dpi:"-588" to "588"(dot)
203dpi:"-392" to "392"(dot)
OPTIONTIME "0", "5" to "200" (x100ms)
AUTO_MEASURE "0": Disable
"1": Enable
AUTO_ONLINE "0": Disable
"1": Enable
FEED "0": Disable
"1": Enable
ONLINE_FEED "0": Disable
"1": Enable
IGNORE_CRLF "0": Do not remove CR/LF
"1": Remove CR/LF
BYTECOMMAND "0": Disable
"1": Enable
IMLVL_RL "0" to "127": reflective sensor
level(Receiving light)
IMLVL_LE "0" to "7": reflective sensor level
(Light emission)
IM_SL "0.0": Automatic setting
"0.1" to "3.3": Manual setting
GAPLVL_RL "0" to "127": transmissive sensor
level(Receiving light)
GAPLVL_LE "0" to "7": transmissive sensor
level (Light emission)
GAP_SL "0.0": Automatic setting
"0.1" to "3.3": Manual setting
RB_NEND "0": Disable
"1": Enable
PRIORITY "0": Prioritize command
"1": Prioritize LCD setting
PRINT_AREA "0": Standard
"1": Left-justify
ADJUSTDARK "0" to "99"
OP_FEED [CL4NX]
609dpi:"0" to "6120" (dot)
305dpi:"0" to "3060" (dot)
203dpi:"0" to "2040" (dot)
[CL6NX]
305dpi:"0" to "3060" (dot)
203dpi:"0" to "2040" (dot)
PASS_SET "0": Disable
"1": Enable
ALL_QTY "0": Disable
"1": Enable
Setting value Default Value
528
initial
R/W
CA
2 R/W ○
2 R/W ○
7 R/W -
0 R/W -
0 R/W -
0 R/W -
0 R/W ○
0 R/W ○
1 R/W ○
0 R/W ○
0 R/W ○
0 R/W ○
0 R/W ○
64 R/W -
3 R/W -
0.0 R/W -
64 R/W -
3 R/W -
0.0 R/W -
1 R/W ○
0 R/W ○
0 R/W ○
50 R/W -
0 R/W ○
0 R/W -
0 R/W ○
Contents of Setting item
Buzzer volume
Power Off Sound
LCD Brightness
Adjust print position
Offset adjust
Pitch and Offset adjust
Waiting time in tear-off mode for
next data
<TW>
Automatic measurement of label
length
Auto online
<AO>, <LD>
Initial feed
Online feed
<LF>
Ignore CR/LF
<CL>
Remove CAN/DLE
<1B>
Adjust reflective sensor level
(Receiving light)
Adjust reflective sensor level
(Light emission)
Reflective sensor slice level
Adjust transmissive sensor level
(Receiving light)
Adjust transmissive sensor level
(Light emission)
Transmissive sensor slice level
Detect ribbon near end
Priority setting
* target command
<#F>, <IG>, <CS>, <A3>,
<PM>
Move printable area
* The head base position and the
Print area are changed in
CL6NX.
Adjust darkness
Optional feed volume
Input password
Display total number of labels to
print