Examples - HP ProCurve 5400zl Reference Manual

Command Line Interface Reference Guide
dhcp-bootp
■
666)
ip-addr
■
■ svlan VLAN-ID
address
■
autoconfig
■
dhcp
■
full
■
■
ipv6-addr
■
link-local
■
ipv6-addr/mask
■
(IPV6-ADDR/PREFIX-LEN)
anycast
■
nodes
eui-64
■
(p. 667)
enable -- Enable IPv6 on an interface and configures an automatically generated link-local addr.
■
(p. 667)
■ [no] svlan VLAN-ID
up to 9220 bytes in size
■ [no] svlan VLAN-ID
all < In | Out | Both > -- Monitor all traffic.
■
mirror
■
mirror_session_name
■
monitor_mirror_session_id
■
■ svlan VLAN-ID
■ svlan VLAN-ID
protocol-group
■
(ASCII-STR)
protocols
■
■ [no] svlan VLAN-ID
dscp -- Specify DSCP policy to use.
■
binary-range
■
integer-range
■
well-defined
■
(Differentiated-Services Codepoint) value and an 802
priority < 0 | 1 | 2 | ... > -- Specify priority to use.
■
■ [no] svlan VLAN-ID
671)
■ [no] svlan VLAN-ID
(p. 672)
■ [no] svlan VLAN-ID
and authenticate voice traffic moving through your network

EXAMPLES

Example: svlan
Configure S-VLANS and ports connected to the customer network:
Edge1 (config)# svlan100
Edge1(svlan-100)# untagged A1
Edge1(svlan-100)# exit
© 2009 Hewlett-Packard Development Company, L.P.
-- Configure the interface to use DHCP/Bootp server to acquire parameters.
-- Interface IP address/mask. (IP-ADDR/mask-LENGTH)
ipv6 -- Configure various IP parameters for the VLAN
-- Set IPv6 parameters for communication within an IP network
-- Automatic address configuration.
-- Configure a DHCPv6 client.
-- Obtain IPv6 address & Configuration information from DHCPv6 server.
rapid-commit -- Obtain IPv6 address quickly from DHCPv6 server.
-- Configure a link-local IPv6 address. (IPV6-ADDR)
-- Configure a link-local IPv6 address.
-- Configure IPv6 address represented in CIDR notation.
(p. 668)
-- Address that is assigned to a set of interfaces that typically belong to different
(p. 665)
-- An IPv6 EUI-64 address that can be automatically configured on any interface
jumbo -- Labels this VLAN as a Jumbo VLAN, allowing you to pass packets
(p. 669)
monitor -- Define either the VLAN is to be monitored or not
-- Mirror destination.
-- Mirror destination name.
name -- Set the VLAN's name (ASCII-STR)
protocol -- Set a predefined protocol for the current VLAN.
-- Enter a list of protocols for the current VLAN delimited by commas.
(p. 671)
< IPX | IPv4 | IPv6 | ... > -- Set a predefined protocol for the current VLAN.
qos -- Set VLAN-based priority
< 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY)
< 0 to 63 > -- Specify the DSCP code-point in decimal.
< af11 | af12 | af13 | ... > -- Define mapping between a DSCP
tagged -- Assign ports to current VLAN as tagged ([ethernet] PORT-LIST)
untagged -- Assign ports to current VLAN as untagged ([ethernet] PORT-LIST)
voice -- Labels this VLAN as a Voice VLAN, allowing you to separate, prioritize,
(p. 665)
(p. 666)
(p. 665)
(p. 669)
< 1 to 4 > -- Mirror destination number.
(p. 671)
(p. 666)
(p. 670)
(p. 668)
(p. 668)
(p. 664)
(p. 671)
(p. 668)
(p. 669)
(p. 669)
(p. 670)
(p. 670)
(p. 670)
(p. 667)
(p. 672)
(p. 672)
svlan
(p.
(p. 667)
(p. 669)
(p. 671)
(p. 666)
(p.
662