OVERVIEW
Category:
Primary context:
Related Commands
Usage:lldp ...
Description: Configuration for LLDP parameter. Provides a standards-based method
COMMAND STRUCTURE
■ lldp
admin-status
receive | disable the port ([ethernet] PORT-LIST)
omodes
■
transmit-receive | disable. (NUMBER)
■ lldp
auto-provision
radio-ports
■
application
auto-vlan
■
controller auto-generated VLAN.
auto-vlan
■
as the radio-ports controller auto-generated VLAN. (VLAN-ID)
■
vlan-base
■
auto-generated VLAN is created for a radio-port application. (VLAN-ID)
■ lldp
config
-- Specify configurational parameters to the port ([ethernet] PORT-LIST)
basicTlvEnable
■
to be advertised. (NUMBER)
dot1TlvEnable
■
vlan-name
■
dot3TlvEnable
■
(p. 356)
ipAddrEnable
■
lldp-ip
■
lldp-ipv6
■
medPortLocation
■
civic-addr
■
COUNTRY
■
■
elin-addr
■
addr
■
medTlvEnable
■
to be advertised. (NUMBER)
© 2009 Hewlett-Packard Development Company, L.P.
Device Discovery
config
show lldp (page 566)
for enabling the switches to advertise themselves to adjacent devices
and to learn about adjacent LLDP devices.
You can also configure the Media Extension Discovery (MED) extension
to LLDP for Voice over IP (VoIP) devices.
-- Set the port in one of the operational mode transmit | receive | transmit &
< TxOnly | RxOnly | Tx_Rx | ... > -- Set the operational mode: transmit | receive |
-- Configure various parameters related to lldp automatic provisioning
-- Configure various parameters related to automatic provisioning for the radio-port
(p. 358)
-- Create a VLAN, with the specified VLAN id value, to be used as the radio-ports
< 2 to 4094 > -- Create a VLAN, with the specified VLAN id value, to be used
auto
--
(p. 353)
< 2 to 4094 > -- Assign the default value of the VLAN id to be used if an
< port_descr | system_name | system_descr | ... > -- Specify the Basic TLV List
(p. 354)
-- Specify the 802.1 TLV List to be advertised.
-- Specify that the VLAN name TLV is to be advertised.
< macphy_config > -- Specify the 802.3 TLV List to be advertised. (NUMBER)
-- Set IP ADDR to be enabled.
-- Set IPV4 ADDR to be enabled. (IP-ADDR)
-- Set IPV6 ADDR to be enabled. (IPV6-ADDR)
-- Configure location-id information to be advertised.
-- Specify the civic location-id information to be advertised
-- Specify the Country Code of two characters. (ASCII-STR)
WHAT
-- Specify the 'what' number of range <0-2>. (NUMBER)
CA-TYPE
-- Specify the ca-type value of range <0-255>. (NUMBER)
■
CA-VALUE
-- Specify the ca-value string. (ASCII-STR)
■
-- Specify the elin address location to be advertised.
-- Specify the Location name to be advertised. (OCTET-STR)
< capabilities | network_policy | location_id | ... > -- Specify the MED TLV List
(p. 357)
(p. 353)
(p. 358)
(p. 354)
(p. 357)
(p. 357)
(p. 357)
(p. 354)
(p. 359)
(p. 355)
(p. 356)
(p. 359)
(p. 357)
(p. 355)
(p. 356)
(p. 359)
(p. 354)
(p. 354)
(p. 356)
(p. 353)
lldp
(p. 353)
352