Command Line Interface Reference Guide
■
■
■
■
md5-auth-key-chain
■
■
passive
■
priority
■
retransmit-interval
■
(p. 273)
transit-delay
■
pim-dense
■
graft-retry-interval
■
resending a Graft on this interface
hello-delay
■
is transmitted on this interface
hello-interval
■
transmitted on this interface
ip-addr
■
241)
■
■
lan-prune-delay
■
max-graft-retries
■
a Graft on this interface
override-interval
■
of a LAN Prune Delay option on this interface
propagation-delay
■
field of a LAN Prune Delay option on this interface
ttl-threshold
■
at which it is not forwarded on this interface
pim-sparse
■
dr-priority
■
election process
hello-delay
■
is transmitted on this interface
hello-interval
■
transmitted on this interface
ip-addr
■
241)
■
■
lan-prune-delay
■
nbr-timeout
■
255)
override-interval
■
of a LAN Prune Delay option on this interface
propagation-delay
■
field of a LAN Prune Delay option on this interface
proxy-arp
■
© 2009 Hewlett-Packard Development Company, L.P.
chain-name
-- Specify key chain to use for MD5 authentication. (ASCII-STR)
■
228)
passive
-- Configures an ospf interface as passive.
priority
< 0 to 255 > -- Set priority of this router as a designated router.
retransmit-interval
< 1 to 3600 > -- Set retransmit interval in seconds; the default is
5.
(p. 273)
transit-delay
< 1 to 3600 > -- Set transit delay in seconds; the default is 1.
-- Set MD5 authentication method and key chain.
chain-name
-- Specify key chain to use for MD5 authentication. (ASCII-STR)
-- Configures an ospf interface as passive.
< 0 to 255 > -- Set priority of this router as a designated router.
< 1 to 3600 > -- Set retransmit interval in seconds; the default is 5.
< 1 to 3600 > -- Set transit delay in seconds; the default is 1.
-- Enable/disable/configure PIM-DM protocol on the VLAN interface
< 1 to 10 > -- Set the interval a PIM router waits for a Graft Ack before
< 0 to 5 > -- Set the maximum time before a triggered PIM Hello message
< 5 to 300 > -- Set the frequency at which PIM Hello messages are
-- Set the source IP address for the PIM-DM packets sent out on this interface
any
-- Dynamically determine IP address.
ip-addr
-- Specify IP address. (IP-ADDR)
-- Turn on/off the LAN Prune Delay Option on this interface
< 1 to 10 > -- Set the maximum number of times this router will resend
(p. 249)
< 500 to 6000 > -- Set the value inserted into the Override Interval field
< 250 to 2000 > -- Set the value inserted into the LAN Prune Delay
< 0 to 255 > -- Set the Time To Live in a PIM-DM State Refresh message
-- Enable/disable/configure PIM-SM protocol on the VLAN interface
-- Set the priority value to use on the interface in the Designated Router
(p. 231)
< 0 to 5 > -- Set the maximum time before a triggered PIM Hello message
< 5 to 300 > -- Set the frequency at which PIM Hello messages are
-- Set the source IP address for the PIM-SM packets sent out on this interface
any
-- Dynamically determine IP address.
ip-addr
-- Specify IP address. (IP-ADDR)
-- Turn on/off the LAN Prune Delay Option on this interface
< 60 to 8000 > -- Set the neighbour loss time interval for this interface
< 500 to 6000 > -- Set the value inserted into the Override Interval field
< 250 to 2000 > -- Set the value inserted into the LAN Prune Delay
-- Enable/disable proxy ARP
(p. 258)
(p. 235)
(p. 236)
(p. 236)
(p. 221)
(p. 241)
(p. 258)
(p. 266)
(p. 279)
(p. 236)
(p. 236)
(p. 221)
(p. 241)
(p. 258)
(p. 266)
(p. 268)
(p. 258)
(p. 265)
(p. 250)
(p. 265)
(p. 279)
(p. 259)
(p. 247)
(p. 247)
interface
(p.
(p. 279)
(p. 228)
(p.
(p. 259)
(p.
(p.
210