HP ProCurve 5400zl Reference Manual page 208

Command Line Interface Reference Guide
provider-network
■
qos -- Set port-based priority
■
dscp
■
binary-range
■
integer-range
■
well-defined
■
(Differentiated-Services Codepoint) value and an 802
priority
■
rate-limit
■
traffic) on the port(s)
all -- Set limits for all traffic.
■
in
■
■
■
out
■
■
■
bcast
■
in
■
■
icmp
■
kbps
■
should be at least 13Kbps, or max-length ICMP packets will fail.)
percent
■
mcast
■
in
■
■
service-policy
■
in -- Apply policy on inbound packets.
■
speed-duplex
■
276)
type < Trunk | | | ... > --
■
unknown-vlans
■
■ [no] interface
(p. 277)
auto -- Cause each port identified in the port list to learn its VLAN membership using the GARP
■
VLAN Registration Protocol (GVRP) ([ethernet] PORT-LIST)
connection-rate-filter
■
blocked by the connection rate filter
unblock
■
all
■
host
■
src-ip
■
dhcp-snooping
■
forbid -- Prevent ports from becoming a member of the current VLAN ([ethernet] PORT-LIST)
■
(p. 234)
ip -- Configure various IP parameters for the VLAN
■
© 2009 Hewlett-Packard Development Company, L.P.
-- Configure qinq port-type as provider-network
(p. 268)
-- Specify DSCP policy to use.
< 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY)
< 0 to 63 > -- Specify the DSCP code-point in decimal.
< af11 | af12 | af13 | ... > -- Define mapping between a DSCP
< 0 | 1 | 2 | ... > -- Specify priority to use.
-- Enable/disable and configure rate-limiting for all traffic (or for incoming ICMP
(p. 271)
-- Set limits for all inbound traffic.
kbps < 0 to 10000000 > -- Specify limit of allowed inbound or outbound traffic in
kilobits-per-second on the specified port(s). Actual limits are in steps of 100Kbps to
100Mbps (granularity is 1% of the lowest related media speed).
percent < 0 to 100 > -- Specify limit as percent of inbound or outbound traffic.
258)
-- Set limits for all outbound traffic.
kbps < 0 to 10000000 > -- Specify limit of allowed inbound or outbound traffic in
kilobits-per-second on the specified port(s). Actual limits are in steps of 100Kbps to
100Mbps (granularity is 1% of the lowest related media speed).
percent < 0 to 100 > -- Specify limit as percent of inbound or outbound traffic.
258)
-- Set limits for broadcast traffic.
-- Set limits for inbound broadcast trafic.
percent < 0 to 100 > --
-- Set limits for ICMP traffic only.
< 0 to 10000000 > -- Specify kilobits-per-second limit of allowed ICMP traffic (values
< 0 to 100 > -- Specify limit as percent of inbound or outbound traffic.
-- Set limits for multicast traffic.
-- Set limits for inbound multicast trafic
percent < 0 to 100 > --
-- Apply the QoS/Mirror policy on the interface (ASCII-STR)
< 10-half | 100-half | 10-full | ... > -- Define mode of operation for the port(s)
(p. 280)
< Learn | Block | Disable > -- Configure GVRP on the port(s)
svlan -- Add, delete, edit SVLAN configuration or enter a SVLAN context (VLAN-ID)
-- Re-enables access to a host or set of hosts that has been previously
-- Resets a host previously blocked by the connection rate filter
-- Resets all previously blocked by the connection rate filter
-- Match packets from the specified IP address. (IP-ADDR)
-- Match packets from the specified subnet. (IP-ADDR/mask-LENGTH)
-- (p. 230)
(p. 231)
(p. 265)
(p. 219)
(p. 238)
(p. 257)
(p. 227)
(p. 238)
(p. 258)
(p. 237)
(p. 249)
(p. 238)
(p. 258)
(p. 238)
(p. 228)
(p. 240)
(p. 267)
(p. 239)
(p. 285)
(p. 246)
(p. 246)
(p. 246)
(p. 275)
(p. 281)
(p. 225)
(p. 281)
(p. 219)
(p. 237)
interface
(p. 227)
(p.
(p.
(p. 258)
(p.
(p. 277)
206