HP ProCurve 5400zl Reference Manual page 742

Command Line Interface Reference Guide
Usage: [no] ip pim-dense [...]
Description: Enable/disable/configure PIM-DM protocol on the VLAN interface.
Next Available Options:
ip-addr -- Set the source IP address for the PIM-DM packets sent out on this
■
lan-prune-delay
■
hello-interval
■
on this interface(p. 725)
hello-delay
■
transmitted on this
graft-retry-interval
■
resending a Graft on this
max-graft-retries
■
Graft on this
override-interval
■
LAN Prune Delay option on this
propagation-delay
■
a LAN Prune Delay option on this
ttl-threshold
■
it is not forwarded on this
pim-sparse
■ [no] vlan VLAN-ID ip pim-sparse
Usage: [no] ip pim-sparse [...]
Description: Enable/disable/configure PIM-SM protocol on the VLAN interface.
Next Available Options:
ip-addr -- Set the source IP address for the PIM-SM packets sent out on this
■
lan-prune-delay
■
hello-interval
■
on this interface(p. 725)
hello-delay
■
transmitted on this
override-interval
■
LAN Prune Delay option on this
propagation-delay
■
a LAN Prune Delay option on this
dr-priority
■
process(p. 722)
nbr-timeout
■
© 2009 Hewlett-Packard Development Company, L.P.
Use direct and 'no' versions of the command to enable/disable
PIM-DM on the interface. Use 'ip pim-dense ?' to get the list
of all configuration options. This command can be used in the
VLAN context or in the global context with the 'vlan <VLAN-ID>'
prefix.
-- Turn on/off the LAN Prune Delay Option on this
< 5 to 300 > -- Set the frequency at which PIM Hello messages are transmitted
< 0 to 5 > -- Set the maximum time before a triggered PIM Hello message is
interface(p. 725)
< 1 to 10 > -- Set the interval a PIM router waits for a Graft Ack before
interface(p. 725)
< 1 to 10 > -- Set the maximum number of times this router will resend a
interface(p. 734)
< 500 to 6000 > -- Set the value inserted into the Override Interval field of a
interface(p. 739)
< 250 to 2000 > -- Set the value inserted into the LAN Prune Delay field of
< 0 to 255 > -- Set the Time To Live in a PIM-DM State Refresh message at which
interface(p. 749)
Use direct and 'no' versions of the command to enable/disable
PIM-SM on the interface. Use 'ip pim-sparse ?' to get the list
of all configuration options. This command can be used in the
VLAN context or in the global context with the 'vlan <VLAN-ID>'
prefix.
-- Turn on/off the LAN Prune Delay Option on this
< 5 to 300 > -- Set the frequency at which PIM Hello messages are transmitted
< 0 to 5 > -- Set the maximum time before a triggered PIM Hello message is
interface(p. 725)
< 500 to 6000 > -- Set the value inserted into the Override Interval field of a
interface(p. 739)
< 250 to 2000 > -- Set the value inserted into the LAN Prune Delay field of
-- Set the priority value to use on the interface in the Designated Router election
< 60 to 8000 > -- Set the neighbour loss time interval for this
interface(p. 743)
interface(p. 743)
interface(p. 729)
interface(p. 733)
interface(p. 729)
interface(p. 733)
interface(p. 737)
vlan
740