HP ProCurve 5400zl Reference Manual page 626

Command Line Interface Reference Guide
tagvalue
■
■ [no] snmpv3
■ [no] snmpv3
user -- Set user that the switch will send messages on behalf. (ASCII-STR)
■
sec-model
■
sec-model12c
■
■
ver3
■
■
■ [no] snmpv3
■ [no] snmpv3
params
■
ipaddr
■
addr-mask
■
filter
■
max-msg-size
■
628)
port-mask
■
retries
■
taglist
■
(p. 631)
timeout
■
udp-port
■
(TCP/UDP-PORT)
ipv6addr
■
addr-mask
■
filter
■
max-msg-size
■
628)
port-mask
■
retries
■
taglist
■
(p. 631)
timeout
■
udp-port
■
(TCP/UDP-PORT)
■ [no] snmpv3
username
■
auth
■
authpassword
■
■
authprotocol
■
■
© 2009 Hewlett-Packard Development Company, L.P.
-- Set tag value that selects entries in the snmpTargetAddr table. (ASCII-STR)
only -- Accept only SNMP v3 messages.
params -- Configure SNMPv3 Target Parameter entry. (ASCII-STR)
-- Set security model.
< ver1 | ver2c > -- Configure SNMPv3 User entry.
message-processing
(p. 628)
-- SNMP version 3 security model.
message-processing
ver3 < noauth | auth | priv > -- Set security level.
■
restricted-access -- Configure SNMPv1 and SNMPv2c access properties.
targetaddress -- Configure SNMPv3 Target Address entry. (ASCII-STR)
-- Set parameter name. (ASCII-STR)
-- Set IP address of the destination target. (IP-ADDR)
-- Set range of transport addresses with this mask. (IP-ADDR)
< None | Debug | All | ... > -- Set log filters.
< 484 to 65535 > -- Set maximum message size value; default is 1472.
-- Set range of udp ports with this mask. (TCP/UDP-PORT)
< 0 to 255 > -- Set retries value; default is 3.
-- Set list of values used to select this entry from snmpNotifyTable. (ASCII-STR)
< 0 to 2147483647 > -- Set time-out value; default is 1500.
-- Set UDP port number to which the messages are sent; default is 162.
(p. 632)
-- Set IPv6 address of the destination target. (IPV6-ADDR)
-- Set range of transport addresses with this mask. (IP-ADDR)
< None | Debug | All | ... > -- Set log filters.
< 484 to 65535 > -- Set maximum message size value; default is 1472.
-- Set range of udp ports with this mask. (TCP/UDP-PORT)
< 0 to 255 > -- Set retries value; default is 3.
-- Set list of values used to select this entry from snmpNotifyTable. (ASCII-STR)
< 0 to 2147483647 > -- Set time-out value; default is 1500.
-- Set UDP port number to which the messages are sent; default is 162.
(p. 632)
user -- Configure SNMPv3 User entry.
-- Set authentication paramaters. (ASCII-STR)
-- Set authentication paramaters.
-- Set authentication password. (ASCII-STR)
priv -- Set Privacy password.
privpassword -- Set Privacy password. (ASCII-STR)
■
privprotocol < DES | AES > -- Set privacy protocol.
■
privpassword
■
< MD5 | SHA > -- Set authentication protocol.
authpassword -- Set authentication password. (ASCII-STR)
priv -- Set Privacy password.
■
privpassword
■
privprotocol < DES | AES > -- Set privacy protocol.
■
privpassword
■
(p. 629)
(p. 631)
< ver1 | ver2c | ver3 > -- Set message processing model value.
(p. 633)
-- Set message processing model value.
(p. 629)
(p. 632)
(p. 625)
(p. 629)
-- Set Privacy password. (ASCII-STR)
(p. 629)
-- Set Privacy password. (ASCII-STR)
-- Set Privacy password. (ASCII-STR)
(p. 629)
(p. 632)
(p. 631)
(p. 628)
(p. 633)
(p. 627)
(p. 626)
(p. 629)
(p. 630)
(p. 632)
(p. 627)
(p. 626)
(p. 629)
(p. 630)
(p. 632)
(p. 633)
(p. 625)
(p. 630)
(p. 630)
(p. 630)
(p. 625)
(p. 625)
(p. 630)
(p. 630)
(p. 630)
snmpv3
(p. 632)
(p. 630)
(p. 632)
(p. 625)
(p.
(p. 625)
(p.
624