Command Line Interface Reference Guide
ist
-- Configure internal spanning tree (IST) instance.
■
port-list
■
PORT-LIST)
path-cost
■
■
■
MSTID
< 1 to 16 > -- ID of the MST instance to configure.
■
port-list
■
path-cost
■
■
■
priority
■
divided into steps of 16 that are numbered from 0 to 15, default is step 8).
priority
■
0-61440 divided into steps of 4096 that are numbered from 0 to 15, default is step 8).
vlan
-- Configure VLANs for the MST instance.
■
VLAN-ID-RANGE
■
(VLAN-ID-RANGE)
■ [no] spanning-tree
mode or in 802.1s native mode. 'spanning-tree legacy-mode' is the equivalent of executing:
spanning-tree legacy-path-cost spanning-tree force-version stp-compatible 'no spanning-tree
legacy-mode' is the equivalent of executing: no spanning-tree legacy-path-cost spanning-tree
force-version mstp-operation
■ [no] spanning-tree
values.
(p. 645)
■ spanning-tree
BPDU is discarded and the information held for a port is aged (default is 20).
■ spanning-tree
it is discarded.
■ spanning-tree
apply
-- Apply pending MSTP configuration (swaps active and pending configuratons).
■
config-name
■
address).
config-name
■
642)
config-revision
■
(default is 0).
instance
■
MSTID
■
vlan
■
■
reset
-- Copy active configuration to pending.
■
■ [no] spanning-tree
for individual ports ([ethernet] PORT-LIST)
admin-edge-port
■
auto-edge-port
■
bpdu-filter
■
assume a continuous fowarding state.
bpdu-protection
■
hello-time
■
global
■
hello-time
■
© 2009 Hewlett-Packard Development Company, L.P.
-- Configure internal spanning tree (IST) instance ports parameters ([ethernet]
(p. 648)
-- Set the internal port pathcost for the IST (default is 'auto').
auto
-- Use dynamic method of selecting a value for the path cost.
path-cost
< 1 to 200000000 > -- Set port's path cost to the fixed value.
-- Configure MST instance ports parameters ([ethernet] PORT-LIST)
-- Set the port pathcost for the instance (default is 'auto').
auto
-- Use dynamic method of selecting a value for the path cost.
path-cost
< 1 to 200000000 > -- Set port's path cost to the fixed value.
< 0 to 15 > -- Set the port priority for the instance (the value is in range of 0-240
< 0 to 15 > -- Set the device priority for the MST instance (the value is in range of
-- VLAN(s) to add to or to remove from the MST instance
(p. 653)
legacy-mode
-- Set spanning-tree protocol to operate either in 802.1D legacy
(p. 644)
legacy-path-cost
max-hops
< 1 to 40 > -- Set the max number of hops in a region before the MST
maximum-age
< 6 to 40 > -- Set maximum age of received STP information before
(p. 645)
pending
-- Manipulate pending MSTP configuration
-- Set the pending MST region configuration name (default is switch's MAC
(p. 642)
-- Specify the configuration name (maximum 32 characters). (ASCII-STR)
< 0 to 65535 > -- Set the pending MST region configuration revision number
(p. 642)
-- Change pending MST instance configuration.
< 1 to 16 > -- ID of the MST instance to configure.
-- Configure VLANs for the MST instance.
VLAN-ID-RANGE
-- VLAN(s) to add to or to remove from the MST instance
(VLAN-ID-RANGE)
(p. 653)
port-list
-- Configure the port-specific parameters of the spanning tree protocol
-- Set the administrative edge port status.
-- Set the automatic edge port detection.
-- Stop a specific port or ports from transmitting BPDUs, receiving BPDUs, and
-- Disable the specific port or ports if the port(s) receives STP BPDUs.
-- Set message transmission interval (in sec.) on the port.
-- Use the globally configured hello-time value.
< 1 to 10 > -- Set message transmission interval (in sec.) on the port.
(p. 644)
(p. 653)
-- Set 802.1D (legacy) or 802.1t (not legacy) default pathcost
(p. 653)
(p. 653)
(p. 648)
(p. 641)
(p. 646)
(p. 641)
(p. 645)
(p. 646)
(p. 641)
(p. 645)
(p. 647)
(p. 643)
(p. 645)
(p. 641)
(p. 641)
(p. 643)
(p. 643)
spanning-tree
(p. 646)
(p. 648)
(p. 646)
(p. 652)
(p. 652)
(p. 641)
(p.
(p. 641)
(p. 643)
639