HP ProCurve 5400zl Reference Manual page 522

Command Line Interface Reference Guide
mcast -- Show limits for ingress multicast traffic.
■
detailed
■
port-list
■
578)
■ show redundancy
■ show rmon
statistics
■
■ show running-config
status -- Check if the running configuration differs from the statup configuration.
■
■ show savepower
■ show services
services
■
details
■
■ show sflow
to 'sflow' (p. 590)
agent -- Displays read-only switch agent information: The agent address is normally the ip
■
address of the first vlan configured.
receiver-index
■
(p. 584)
destination
■
which the sampling-polling data is sent.
sampling-polling
■
port-list
■
578)
■ show snmp-server
response/trap source-ip policy configured on the switch
community
■
traps -- Show all configured traps.
■
■ show snmpv3
access-rights
■
group
■
sec-model
■
■
■
community
■
COMMUNITY-NAME
■
enable -- Show SNMPv3 status.
■
engineid
■
group -- Show SNMPv3 User to Group mappings.
■
group
■
user
■
■
notify -- Show SNMPv3 notification table.
■
NOTIFY-NAME
■
only -- Show SNMP message reception policy.
■
params
■
PARAM-NAME
■
restricted-access
■
targetaddress
■
TARGETADDR-NAME
■
user -- Show SNMPv3 users.
■
USER-NAME
■
© 2009 Hewlett-Packard Development Company, L.P.
-- Show Inbound Radius Override details.
-- Specify ports for which information will be shown. ([ethernet] PORT-LIST)
-- Display redundant information for Management and Fabric Modules
-- Show detailed rmon statistics for the ports
-- Show RMON statistics for the ports ([ethernet] PORT-LIST)
-- Show the switch running configuration
-- Shows the user configured block power status
-- Show services information
-- Show services information (SLOT-ID)
-- (p. 547)
-- Display information regarding the configuration, sampling, and polling with respect
< 1 to 3 > -- Select one of the three possible sFlow receiver tables. (NUMBER)
-- Displays information about the receiver/collector/management-station to
-- Displays information about sampling and polling.
-- Displays information about sampling and polling. ([ethernet] PORT-LIST)
-- Display information on all SNMP communities, trap receivers and Snmp
-- Specify SNMP community to which to restrict the output. (ASCII-STR)
-- Show configuration of SNMPv3 features.
-- Show information about access rights.
< ManagerPriv | ManagerAuth | OperatorAuth | ... > -- Show SNMPv3 users.
-- Set security model.
ver1-2c < ver1 | ver2c > -- Configure SNMPv3 User entry.
ver3 -- SNMP version 3 security model.
ver3 < noauth | auth | priv > -- Set security level.
■
-- Show SNMPv3 Community table.
-- Show a specific community entry. (ASCII-STR)
-- Show switch's SNMP engineId.
< ManagerPriv | ManagerAuth | OperatorAuth | ... > -- Show SNMPv3 users.
-- Show a specific user. (ASCII-STR)
sec-model < ver1 | ver2c | ver3 > -- Show a specific security model.
-- Show a specific notification entry. (ASCII-STR)
-- Show SNMPv3 Target Parameters table.
-- Show a specific Target Parameter entry. (ASCII-STR)
-- Show SNMPv1 and SNMPv2c access properties.
-- Show SNMPv3 Target Address table.
-- Show a specifc target address entry. (ASCII-STR)
(p. 601)
-- Show a specific user. (ASCII-STR)
(p. 569)
(p. 546)
(p. 586)
(p. 589)
(p. 589)
(p. 529)
(p. 546)
(p. 591)
(p. 599)
(p. 589)
(p. 602)
(p. 539)
(p. 550)
(p. 550)
(p. 553)
(p. 601)
(p. 574)
(p. 574)
(p. 575)
(p. 602)
(p. 594)
(p. 588)
(p. 589)
(p. 589)
(p. 591)
(p. 527)
(p. 602)
(p. 602)
(p. 539)
(p. 574)
(p. 575)
(p. 586)
(p. 597)
show
(p.
(p. 585)
(p. 596)
(p.
(p. 539)
(p. 553)
(p. 553)
(p. 589)
(p. 597)
520