HP ProCurve 3500-24 Reference Manual

Hp procurve 3500-24: reference guide.
Hide thumbs
HP ProCurve Switch 8200zl, 5400zl, 3500, and 6200yl Series
Technical overview
Table of contents
Executive summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Core to edge: 8200zl, 5400zl, 3500, and 6200yl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
HP ProCurve Switch 8200zl series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
HP ProCurve Switch 5400zl and 3500 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
HP ProCurve Switch 6200yl-24G-mGBIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
ProVision ASIC architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Inside the ProVision ASIC architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Classification and lookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Policy Enforcement Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Network switch engine programmability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Fabric Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
ProVision ASIC CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Fabric ASIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Advertising

   Also See for HP ProCurve 3500-24

   Related Manuals for HP ProCurve 3500-24

   Summary of Contents for HP ProCurve 3500-24

  • Page 1

    HP ProCurve Switch 8200zl, 5400zl, 3500, and 6200yl Series Technical overview Table of contents Executive summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Introduction .

  • Page 2: Table Of Contents

    Switch 8200zl series-specific modules and components . . . . . . . . . . . . . . . . .

  • Page 3: Table Of Contents

    LED status indicators for Switch 3500 and 6200yl series . . . . . . . . . . . . . . . .

  • Page 4: Executive Summary, Introduction

    HP ProCurve Switch 5406zl Intelligent Edge (J8697A) The HP ProCurve Switch 5406zl is a 4U switch (6 . 9 inch/17 .53 cm) that can hold up to 6 zl interface and service modules and can provide up to either 144 Gigabit ports or 24 10-Gigabit ports . The throughput of the...

  • Page 5

    HP ProCurve Switch 5412zl Intelligent Edge (J8698A) The HP ProCurve Switch 5412zl is a 7U switch (12 . 1 inch/30 .73 cm) that can hold up to 12 zl interface and service modules and can provide up to either 288 Gigabit ports or 48 10-Gigabit ports . The throughput of the 5412zl switch fabric is capable of up to 480 .3 Mpps with a backplane speed of 691 .2 Gbps .

  • Page 6: Core To Edge: 8200zl, 5400zl, 3500, And 6200yl, Overview

    Layer 3 stackables is designed to be deployed as an aggregator of traffic from the edge to the core of the network . The HP ProCurve Switch 5400zl series provides the same Intelligent Edge features as the 3500 series, with baseline high availability in a modular form factor . The HP ProCurve Switch 8200zl series offers advanced resiliency and redundancy and brings to the portfolio a highly available switch platform for mission-critical access layer through mid-sized core deployments .

  • Page 7: Hp Procurve Switch 8200zl Series, Hp Procurve Switch 5400zl And 3500 Series

    The Switch 5400zl and 3500 series are targeted as enterprise-class wiring closet switches—designed for low cost with a choice of medium to high port density . Voice, video, and data ready, the HP ProCurve Switch 5400zl and 3500 series offer extensive prioritization features that bring full convergence down to the desktop .

  • Page 8: Hp Procurve Switch 6200yl-24g-mgbic, Provision Asic Architecture

    HP ProCurve Switch 6200yl-24G-mGBIC The HP ProCurve Switch 6200yl-24G-mGBIC is an advanced Layer 3 stackable at 1U height . It has 24 mini- GBIC slots and an expansion slot for an optional 4-port 10-GbE module . Designed to be deployed as an aggregator of traffic from the edge to the core of the network, this switch supports a variety of Gigabit mini- GBICs, such as SX, LX, LH, and 1000Base-T .

  • Page 9: Inside The Provision Asic Architecture, Classification And Lookup, Policy Enforcement Engine, Network Switch Engine Programmability

    All of the key elements are connected to the active backplane . The active backplane contains the switch fabric and distributes power to all modules . The HP ProCurve Switch 5400zl, 3500, and 6200yl series have similar architectural components . The primary difference in the illustration would be the number of ports supported .

  • Page 10: Fabric Interface, Provision Asic Cpu, Fabric Asic

    HP ProCurve Switch 4000M and Switch 5300xl new ASIC-related features well after initial release of those products . The customers’ investments in the HP ProCurve Switch 4000M and 5300xl are preserved by new functionality not otherwise possible without the ASIC NPU programmability .

  • Page 11: Advanced Capabilities Of The Product Family, Versatile Intelligent Port (vip), Provision Hardware Resiliency

    (labeled A through F) will remain powered on, so critical network connections should be prioritized toward the top of the switch . A minimum of one power supply is required for proper operation of all 6 slots in a Switch...

  • Page 12: Switch 8212zl Chassis Layout

    • Intelligent Edge features and IP Base Routing features standard Switch 8212zl Chassis layout The Switch 8212zl is a rack-mountable, 9U-height chassis . The interface modules are inserted in the front slots, labeled A through L . Management and fabric modules are labeled MM1/MM2 and FM1/FM2, respectively . Figure 2. J8715B HP ProCurve Switch 8212zl Base System slot labeling (MM = Management Module;...

  • Page 13: Switch 8206zl Chassis Layout, Switch 8200zl Series-specific Modules And Components

    “active” MM (either MM1 or MM2) . If the active MM were to fail, the standby MM takes control of the switch and continues operation . However, if only one management module is running and then is removed, all ports lose communication and the system will be powered down .

  • Page 14

    The HP ProCurve Switch 8200zl series requires at least a single management module that oversees (or “supervises”) the operation of the interface modules and fabric modules . The management module is responsible for network control processing (e .g ., OSPF updates or ARP requests), while each interface module in conjunction with the fabric modules handles the traffic switching in ASIC hardware .

  • Page 15

    The switching fabric is provided by two fabric modules, each housing a single ProVision Fabric ASIC . Much like the design of the award-winning HP ProCurve Switch 5412zl, the Fabric ASICs are load-sharing and resilient to each other . With both fabric ASICs operational, all 12 slots of the Switch 8212zl provide wire-speed switching capacity for up to 288 Gigabit ports, or up to 28 .8 Gbps per slot when used with 10-Gigabit ports .

  • Page 16

    All components contained on the SSM are very low failure rate functions (as evidenced from the very low failure rate of HP ProCurve 5400zl series chassis and predecessor chassis products) . But in the event of a failure of any of these components, this module can be replaced without removing any network cables or interface modules—as required by other competitor designs when there is a need to service some components mounted...

  • Page 17

    The fan tray is hot-swappable in the Switch 8212zl; it can be removed and replaced without removing power from the switch . However, the new fan tray should be installed immediately after removing the old fan tray to avoid overheating and the automatic switch shutdown within three minutes .

  • Page 18

    8206zl fan tray consists of four fans . The fan speed is based on the sensed ambient temperature of the chassis . As with the Switch 8212zl, the fan tray is installed/replaced from the rear of the chassis and mounted on the left side of the chassis (from a front-view perspective) .

  • Page 19

    The fan tray is hot-swappable in the Switch 8206zl; it can be removed and replaced without removing power from the switch . However, the new fan tray should be installed immediately after removing the old fan tray to avoid overheating and the automatic switch shutdown within three minutes .

  • Page 20: Hp Procurve Switch 5400zl Series

    Premium License, described later in this document . The Switch 5400zl series is the latest generation of managed chassis products from HP ProCurve . The 5400zl series follows in the evolution of HP ProCurve managed chassis switches, featuring Power over Ethernet (PoE) on every copper port, chassis flexibility in the stackable price range, and a scalable architecture .

  • Page 21

    Figure 11. HP ProCurve Switch 5400zl chassis and bundles HP ProCurve Switch 5406zl Chassis HP ProCurve Switch 5412zl Bundles HP ProCurve Switch 5406zl HP ProCurve Switch 5412zl (J8697A) (J8698A) HP ProCurve Switch 5412zl-96G HP ProCurve Switch 5406zl-48G (J8699A) (J8700A) HP ProCurve 5412zl-96G-PoE+ Switch...

  • Page 22: Zl Series Chassis Layout

    5400zl series chassis layout The HP ProCurve Switch 5406zl chassis is rack-mountable with a 4U height, and the Switch 5412zl chassis is rack-mountable with a 7U height . The line interface modules are inserted in the front slots, labeled A through F on the 5406zl, and A through L on the 5412zl .

  • Page 23: Zl Chassis Layout

    5406zl chassis layout Figure 12. HP ProCurve Switch 5406zl chassis layout Front Slot A Slot C Slot E Back EPS 1 Provided a second power supply remains operational 5412zl chassis layout Figure 13. HP ProCurve Switch 5412zl chassis layout Front...

  • Page 24: Fan Tray, Zl Management Module

    Figure 14. Fan tray for HP ProCurve Switch 5406zl (J8697-60005) 5400zl management module All configurations of the HP ProCurve Switch 8200zl/5400zl series include a single management module that oversees the operation of the line interface modules and switch fabric . The management module incorporates an RS-232 serial port for local management and configuration .

  • Page 25: Zl Power Supplies

    As indicated in the following figure, the internal power supply provides both system power as well as PoE . The HP ProCurve Switch 8200zl/5400zl series, as well as the 3500 series, can power any device that adheres to the IEEE 802 .3af standard . The HP ProCurve Switch 8200zl/5400zl series can power any device that adheres to the IEEE 802 .3at standard, when PoE+ zl modules are used in conjunction with PoE+ power supplies .

  • Page 26: Zl Modules, Interface Modules

    . An external power shelf, the HP ProCurve Switch zl Power Supply Shelf, is available to house up to two Switch zl power supplies . The power supplies in the Power Supply Shelf can be connected to one or two 8200zl/5400zl switches to provide additional PoE/PoE+ power, either to power additional PoE-powered devices, or to provide more power for PoE power redundancy .

  • Page 27: Services Modules

    20-port 10/100/1000 PoE+ / 4-port MiniGBIC 24-port 10/100 PoE+ Services modules The HP ProCurve Switch 8200zl/5400zl series supports a variety of services modules, providing customers with the ability to deploy integrated network applications and services for enhanced system security and functionality .

  • Page 28: Power Supply Configurations

    1+1 power supply redundancy implies providing twice the minimum number of supplies required to power the system . Table 3 shows the HP ProCurve Switch 5400zl and 8200zl series minimum and maximum internal power supply configurations, as well as internal combined power with external power shelf configurations .

  • Page 29

    Tables 4 and 5 show examples of the maximum number of PoE or PoE+ ports that can be supported by the Switch 8206zl and 5406zl . Table 4 shows the maximum number of PoE ports at full power (Class 0—15 .4 watts), and the next section shows the maximum number of PoE ports at phone power (8 watts) for each configuration .

  • Page 30

    Tables 6 and 7 show examples of the maximum number of PoE or PoE+ ports that can be supported by the Switch 8212zl and 5412zl . Table 6 shows the maximum number of PoE ports at full power (Class 0—15 .4 watts), and the next section shows the maximum number of PoE ports at phone power (8 watts) for each configuration .

  • Page 31: Specifications—management Module

    DB-9 male connector mounted on the front panel . To connect to the console, a standard null modem cable is used equivalent to that used for other HP ProCurve switches like the HP ProCurve Switch 5300xl series .

  • Page 32: Specifications—interface Modules

    Specifications—interface modules The following is a description of the interface modules supported by the HP ProCurve Switch 5400zl and 8200zl series . HP ProCurve Switch zl 24-Port 10/100/1000 PoE Module (J8702A) Description This interface module has 24 10/100/1000Base-T ports that provide Gigabit-over-copper connectivity for wiring closets, enabling high-density Gigabit connectivity to the desktop over Category 5 copper cabling .

  • Page 33

    This interface module has 24 mini-GBIC ports and is appropriate for use as an aggregator in a distribution environment . This module supports the same mini-GBICs as the HP ProCurve Switch zl 20-Port 10/100/1000 + 4-Port Mini-GBIC Module previously described . The mini-GBICs are ordered separately .

  • Page 34

    • 15 m using CX4 cable • 300 m using optical media converters and multimode fiber cable NOTE Use CX4 10-GbE cable (0 .5 m–15 m) or HP ProCurve 10-GbE CX4 Media Converter (J8439A) HP ProCurve 24-Port 10/100/1000 PoE+ zl Module (J9307A) Description This interface module has 24 10/100/1000Base-T ports that provide Gigabit-over-copper connectivity for wiring closets, enabling high-density Gigabit connectivity to the desktop over Category 5 copper cabling .

  • Page 35

    HP ProCurve 20-Port 10/100/1000 PoE+ and 4-Port Mini-GBIC zl Module (J9308A) Description This interface module has 20 10/100/1000Base-T ports that provide Gigabit-over-copper connectivity for wiring closets, enabling high-density Gigabit connectivity to the desktop over Category 5 copper cabling . Each port is capable of providing IEEE 802 .3af/at compliant Power over Ethernet and Power over Ethernet Plus (PoE+) to power IP phones, wireless access points, and other devices .

  • Page 36: Specifications—services Modules

    Duplex: half or full Connectors: RJ-45 Specifications—services modules The following is a description of the services modules supported by the HP ProCurve Switch 5400zl and 8200zl series . HP ProCurve Wireless Edge Services zl Module (J9051A) HP ProCurve Redundant Wireless Services zl Module (J9052A)

  • Page 37

    40°C . The HP ProCurve ONE Services zl Module can only be used with certified OA services applications . It does not support a general application environment .

  • Page 38: Hp Procurve Switch 3500 Series

    Use of the HP ProCurve Threat Management Services zl Module restricts the temperature specification for the 5400zl series switch to 50°C if all installed modules are on the left side of the chassis . If any installed module is on the right side of the chassis, the temperature specification of the entire switch is limited to 40°C .

  • Page 39

    . It doubles the available PoE power from 398 W to 796 W for up to two Power over Ethernet capable Switch 3500 series . The HP ProCurve 620 RPS/EPS also provides redundant system power for up to two 3500...

  • Page 40: Specifications

    3500-48-PoE* 3500-48-PoE + HP ProCurve 620 * Also these figures indicate the number of ports that are 1+1 with the use of the HP ProCurve 620 Redundant/External Power Supply Specifications Processor The CPU processor is a Freescale PowerPC 8540 operating at 667 MHz .

  • Page 41: Hp Procurve Switch 6200yl

    • J8440A HP ProCurve 10-GbE X2-CX4 Transceiver NOTE Only the two fixed CX4 ports on this module support the HP ProCurve 10-GbE CX4 Media Converter (J8439A) . HP ProCurve Switch 6200yl The HP ProCurve Switch 6200yl-24G-mGBIC is an advanced Layer 3 stackable in 1U height . It has 24 mini- GBIC slots and an expansion slot for an optional 4-port 10-GbE module .

  • Page 42

    Switch yl 10-GbE 2-Port CX4 + 2-Port X2 Module . This module is installed on the back panel of the switch . This is the same module that is supported by the HP ProCurve Switch 3500 series . Refer to the section covering the...

  • Page 43: Overview Of Features And Benefits, Performance, Security Features

    IP Base Routing feature set is also standard; an optional Premium License is available to enable Advanced Routing features . For the HP ProCurve Switch 6200yl, the Advanced Routing feature set is also standard . The IP Base Routing feature set includes Static Routing and RIP . In addition to OSPF, the Advanced Routing feature set includes additional aggregation layer features: Q-in-Q, PIM-SM, PIM-DM, OSPF-ECMP, and VRRP .

  • Page 44: Qos Functions

    Web server – Concurrent IEEE 802 . 1 X, Web, and MAC authentication schemes per port: switch port will accept up to 32 sessions of IEEE 802 . 1 X, Web, and MAC authentications • Access control lists (ACLs): provide filtering based on the IP field, source/destination IP address/subnet, and...

  • Page 45: Convergence, Layer 2 Switching, Bridging Protocols, Routing Protocols, Ipv6

    QoS and VLAN to automatically configure network devices such as IP phones • PoE allocations: supports multiple methods (automatic, IEEE 802.3af/at class, LLDP-MED, or user specified) to allocate PoE/PoE+ power for optimal energy saving • iSCSI support: enables the deployment of Ethernet storage area network solutions using the iSCSI standard • L2/L3 jumbo frames: Layer 2/Layer 3 jumbo frames provide scalability in throughput Layer 2 switching • HP ProCurve switch meshing: dynamically load-balances across multiple active redundant links to increase available aggregate bandwidth • VLAN support and tagging: support for complete IEEE 802.1Q standard and 2,048 VLANs simultaneously • IEEE 802.1v protocol VLANs: isolate select non-IPv4 protocols automatically into their own VLANs • GVRP: Group VLAN Registration Protocol allows automatic learning and dynamic assignment of VLANs • Q-in-Q: increases the scalability of Ethernet networks by providing a hierarchical structure; connects multiple LANs on high-speed campus or metro Ethernet network Bridging protocols • MSTP: provides high link availability in multiple VLAN environments by allowing multiple spanning trees;...

  • Page 46: Multicast Protocols, High Availability And Redundancy, Management

    – The Switch 8212zl/5412zl provides slots for four internal supplies . This can provide 1+1 redundancy similar to the Switch 5406zl . You can use the internal supplies for 1+1 backup; two backing up two for both PoE and system power needs .

  • Page 47: Diagnostics, Future-proofing, Low Cost Of Ownership, Standards And Protocols, Device Management, General Protocols

    • Industry-leading warranty: lifetime warranty* features next-business-day advance replacement, including coverage for fans and power supplies . * HP ProCurve Switch 3500/5400/6200/8200 lifetime warranty is subject to local law and regulation; see Warranty Statement for more details. See www.procurve.com/support for more details on support and software releases. Standards and protocols...

  • Page 48: Ip Multicast, Ipv6

    RFC 4113 MIB for UDP RFC 4251 SSHv6 Architecture RFC 4252 SSHv6 Authentication RFC 4253 SSHv6 Transport Layer RFC 4254 SSHv6 Connection RFC 4293 MIB for IP RFC 4419 Key Exchange for SSH RFC 4541 IGMP & MLD Snooping Switch...

  • Page 49: Mibs, Network Management, Qos/cos, Security

    MIBs RFC 1213 MIB II RFC 1493 Bridge MIB RFC 1724 RIPv2 MIB RFC 1850 OSPFv2 MIB RFC 2021 RMONv2 MIB RFC 2096 IP Forwarding Table MIB RFC 2613 SMON MIB RFC 2618 RADIUS Client MIB RFC 2620 RADIUS Accounting MIB RFC 2665 Ethernet-Like-MIB RFC 2668 802 .3 MAU MIB RFC 2674 802 .

  • Page 50: Performance And Capacity, Capacity And Performance Features Comparison

    The following table provides a comparison of several categories of capacity and performance levels for the HP ProCurve Switch 8200zl, 5400zl, 3500, and 6200yl series . These include the routing and switching capacity (Gbps), switch fabric speed (Gbps), maximum number of 1 Gbps ports that can operate concurrently at wire-speed, maximum number of 10 Gbps ports that can operate concurrently at wire-speed, and the size of the routing table (entries) .

  • Page 51: Per-port Buffer Sizes, Routing And Forwarding Tables

    Per-port buffer sizes The HP ProCurve Switch 8200zl, 5400zl, 3500, and 6200yl series have eight hardware queues to which prioritized traffic can be assigned . Software can designate a certain amount of output memory buffer for each queue to minimize the impact from events that exceed line rate such as bursty network traffic . Users can choose to configure the number of queues—2, 4, or 8—so that they can optimize the amount of memory buffer...

  • Page 52: Optimizing The 10-gbe Port Configuration

    As illustrated in the figure below, internally, there are two 14 .4 Gbps channels between each 4-port 10-GbE module and the switch fabric . Figure 21. 10-GbE module architecture showing ports grouped by 14.4 Gbps channel. Architecture model applies to the HP ProCurve Switch 8200zl, 5400zl, select 3500, and 6200yl series product lines.

  • Page 53: Throughput And Latency Performance Data

    The following measurements were performed by HP ProCurve using test equipment manufactured by Ixia Communications (www .ixiacom .com) . In these tests, the maximum number of supported ports on the HP ProCurve Switch 5412zl was used . Proportional performance results at 100% of throughput are achieved on...

  • Page 54

    Table 14. Throughput performance 10 Gbps Packet size 1024 1280 1518 1 Gbps Packet size 1024 1280 1518 100 Mbps Packet size 1024 1280 1518 See the explanation about 10 Gigabit performance traffic patterns in the next section . Packets per Full mesh Throughput % second...

  • Page 55: Gigabit Performance Traffic Patterns, Throughput Test, Latency Measurements

    . For example, consider a worst case scenario where the average packet size is 64 bytes . This would result in a throughput of approximately 70% to 80% of the rated wire-speed capacity . HP ProCurve considers such minimum-sized packet traffic scenarios being realized over an extended period of time to be extremely atypical and unlikely to be experienced by customers in the field .

  • Page 56: Hp Procurve Warranty And Support, Industry-leading Warranty

    Controller . The following hardware products and their related series modules have a one-year hardware warranty with extensions available: HP ProCurve Routing Switch 9300m series, HP ProCurve Switch 8100fl series, HP ProCurve Network Access Controller 800, and HP ProCurve DCM Controller . The following hardware products have a one-year hardware warranty with extensions available: HP ProCurve M111 Client...

  • Page 57: Appendix A: Premium License, Intelligent Edge, Ip Base Routing, Advanced Routing Features

    • PCM—You use HP ProCurve Manager to perform the most common licensing functions . If you are already using PCM, this is more convenient than the manual method . There is a free copy of HP ProCurve Manager on the CD-ROM that accompanies your Premium License .

  • Page 58

    Either method requires that you be registered on the My ProCurve Web portal . To use HP ProCurve Manager to install a Premium License, you first select the Switch 5400zl or 3500 series in the PCM navigation tree and right-click it . Then, you select Config Manager > License Software on the pop-up menus .

  • Page 59

    Premium License . The registration ID is found on a plastic laminated card that is shipped with the HP ProCurve switch . After you agree to the terms of the License Agreement, the wizard will display the status of the license installation process .

  • Page 60: Appendix B: Policy Enforcement Engine, Policy Enforcement Engine Benefits

    In the initial release, the contents of the TCAM are common among the multiple line interface modules that a switch may have installed . For example, a HP ProCurve Switch 5406zl or 8206zl may have up to 6 line interface modules, and a HP ProCurve Switch 5412zl or 8212zl may have up to 12 line interface modules .

  • Page 61: Appendix C: Power Over Ethernet, Poe/poe+ Device Types, Power Delivery Options

    (47 to 57 volts DC) and wattage (up to 15 .4 watts), with further limitations on the devices that receive power . HP ProCurve switches that are PoE-enabled support both IEEE 802 .3af-compliant devices as well as some pre- 802 .3af standard devices .

  • Page 62: Poe Negotiation, Additional Poe Power—external Supplies, Support For Pre-802 .3af Standard Powered Devices

    The IEEE 802 .3af standard requires power sourcing equipment (PSE) to choose between the options . It is not possible to mix and match or to use all pairs for power transmission . HP ProCurve switches provide power over the data pairs . However, the standard requires PDs to be able to accept power over either data pairs or unused pairs .

  • Page 63: Appendix D: Pim Sparse Mode

    Appendix D: PIM Sparse Mode In Protocol Independent Multicast-Sparse Mode (PIM-SM), the assumption is that there are no hosts that want the multicast traffic unless they specifically ask for it . In contrast, PIM Dense Mode (PIM-DM) assumes downstream router membership unless it receives an explicit prune message . PIM-SM is appropriate for wide- scale deployment for both densely and sparsely populated groups and is the optimal choice for all production networks regardless of size and membership density .

  • Page 64: Appendix E: Lldp-med

    HP ProCurve switches to advertise themselves to adjacent devices and to learn about adjacent LLDP devices . An LLDP packet transmitted by an HP ProCurve switch contains data about the switch and port . The switch advertises itself to adjacent (neighbor) devices by transmitting LLDP data packets out all ports on which outbound LLDP is enabled, and reading LLDP advertisements from neighbor devices on ports that are inbound LLDP-enabled .

  • Page 65: Appendix F: Virus Throttle Security

    • Class 3 (Communication Devices): These devices are typically IP phones or end-user devices that otherwise support IP media and offer all Class 1 and Class 2 features, plus location identification and emergency 911 capability, Layer 2 switch support, and device information management . Appendix F: Virus Throttle security Virus Throttle is based on the detection of anomalous behavior of network traffic that differs from a normal activity .

  • Page 66: Response Options, Sensitivity, Connection-rate Acl

    On the HP ProCurve Switch 8200zl, 5400zl, 3500, and 6200yl series, Virus Throttle is implemented through connection-rate filtering . When connection-rate filtering is enabled on a port, the inbound routed traffic is monitored for a high rate of connection requests from any given host on the port . If a host appears to exhibit the worm-like behavior of attempting to establish a large number of outbound IP connections in a short period of time, the switch responds on the basis of how connection-rate filtering is configured .

  • Page 67: Appendix G: Vrrp

    The advantage gained from using VRRP is a default path with higher availability, but without requiring configuration of dynamic routing or router discovery protocols on every end host . VRRP on HP ProCurve switches is interoperable with other routers that support RFC 3768 . VRRP operational aspects include: • Preempt delay timer to allow other protocols to complete their convergences...

  • Page 68: Xrrp Support On Switch 5300xl Series, Appendix H: Ospf Equal Cost Multipath

    Similar in concept to VRRP, the HP ProCurve XL Router Redundancy Protocol (XRRP) provides the equivalent mechanism in the HP ProCurve Switch 5300xl series for backup functionality . Like VRRP, XRRP presents a virtual router to the end-node connections whose IP and MAC address can transition from the master HP ProCurve Switch 5300xl to the backup HP ProCurve Switch 5300xl in the event the master HP ProCurve Switch 5300xl interface fails .

  • Page 69: Appendix I: Advanced Classifier-based Qos

    – Layer 3 IP precedence bits – Layer 3 DSCP bits – Layer 4 UDP/TCP application port (including TCP flags) – VLAN ID • Additional policy actions to manage selected traffic, such as rate-limiting and IP precedence marking • Configuring service policies for features such as quality of service (QoS) and traffic mirroring • The application of service policies to specific inbound traffic flows on individual ports and VLAN interfaces (rather than only on switch-wide or port-wide traffic) Figure A9. Advanced Classifier-Based QoS model...

  • Page 70: Appendix J: Server-to-switch Distributed Trunking

    Layer 2 network . Distributed Trunking (DT) is included in switch software starting with version K . 1 4 . In this initial release, only Server-to-Switch Distributed Trunking is supported . For each downstream server, it sees the aggregated links as coming from a single switch, which makes any servers that support standard IEEE 802 .3ad interoperate with...

  • Page 71: Limitations/restrictions, Appendix K: Troubleshooting, Led Status Indicators For Switch 8200zl Series

    An example of upstream traffic forwarding is as follows Assuming the uplink connected to Switch B is blocked by STP and only an uplink in Switch A is active . Server 1 sent traffic with load-balance across its 802 .3ad LACP links . If the receiving switch is Switch A, which learns the destination MAC from any of the upstream links, it will forward the unicast frames to destination directly via its upstream link .

  • Page 72

    Normal operation . Blinking (orange) One or more of the switch’s fans have failed . The switch Fault LED will be blinking simultaneously . On (green) A power supply is installed in the position in the back of the switch corresponding to the number, and the supply is plugged into an active AC power source .

  • Page 73: Led Status Indicators For Switch 5400zl Series

    The LED status indicators for the HP ProCurve Switch zl modules (used in the 8212zl, 8206zl, 5406zl, and 5412zl chassis) are described in the following table . Table A2: LED status indicators for HP ProCurve Switch 8200zl and 5400zl series—switch modules...

  • Page 74

    A power supply is installed in the position in the back of the switch corresponding to the number, and the supply is plugged in to an active AC power source . As shipped, the switch has a single power supply in position 1 .

  • Page 75: Led Status Indicators For Switch 3500 And 6200yl Series

    • Whether PoE power is being supplied or not LED status indicators for Switch 3500 and 6200yl series The front panel of the HP ProCurve Switch 3500 and 6200yl series has various LED status indicators that are described in the following table . Table A5: LED status indicators for HP ProCurve Switch 3500 and 6200yl series...

  • Page 76: Part Numbers And Field Replaceable Units

    Mode) LED Mode Select * The HP ProCurve Switch 3500-24, 3500-48, 3500-24-PoE, and 3500-48-PoE do not support the 10-GbE module . ** The HP ProCurve Switch 3500-24 (J9470A) and 3500-48 (J9472A) do not support PoE . Part numbers and Field Replaceable Units Appendix L lists various part numbers and Field Replaceable Units (FRUs) for the HP ProCurve Switch 8200zl, 5400zl, 3500, and 6200yl series .

  • Page 77: Appendix L: Part Numbers And Field Replaceable Units

    Appendix L: Part numbers and Field Replaceable Units The table following lists various part numbers and Field Replaceable Units (FRUs) for the HP ProCurve Switch 8200zl and 5400zl series . Table A6: Part numbers and FRUs for HP ProCurve Switch 8200zl and 5400zl series...

  • Page 78

    5069-5705 356578-B21 The following tables (A8 & A9) list the part numbers of power cords that can be used with the HP ProCurve Switch 8200zl, 5400zl, 3500, and 6200yl series products . The power cords available for these switches are sized for the increased current that can be drawn, meeting the needs of PoE .

  • Page 79: For More Information

    Table A9: Power cords for HP ProCurve Switch 8200zl and 5400zl series. Country 1500 W PoE+ power supply Australia/New Zealand 8121-0857 China 8121-1034 Continental Europe 8120-5336 Denmark 8120-5340 Israel 8121-1009 Japan 8120-5342 South Africa/India 8120-5341 Switzerland 8120-5339 Taiwan 8121-0941 Thailand 8121-0671 U .K .

  • Page 80

    © Copyright 2009 Hewlett-Packard Development Company, L .P . The information contained herein is subject to change without notice . The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services . Nothing herein should be construed as constituting an additional warranty .

This manual also for:

Procurve 5400zl

Comments to this Manuals

Symbols: 0
Latest comments: