Command Structure - HP ProCurve 5400zl Reference Manual

Command Line Interface Reference Guide
administrator.
o location ASCII-STR - Up to 48 characters. Description of the
switch location.
o community ASCII-STR - Enter up to 32 characters to name an SNMP
community.
o <manager|operator> - manager - the community can access all MIB
objects; operator (default) - the community can access all except
the CONFIG MIB.
o <restricted|unrestricted> - unrestricted - any MIB variable that
has read/write access can be set; restricted (default) - MIB
variables cannot be set, only read.
o IP-ADDR - Address of the network management station.
o [none|all|not-info|critical|debug] - The level of Switch
events that will generate a Trap to be sent: none - send no log
message; all - send all log messages; not-info - send each log
message that is not informational-only; critical - send
critical-level log messages; debug (reserved for Internal use).
o [IP-ADDR|loopback<0-7>|dst-ip-of-request] - Policy type used to
fill the source-ip address field of the snmp response/trap pdu:
IP-ADDR - This ip address will be used while sending the
snmp response/trap pdu; loopback<0-7> - lexicographically min.
configured ip address on specified loopback interface will be
used while sending the response; dst-ip-of-request - destination
ip address passed in the request pdu will be send as the source-ip
address in the response pdu.

COMMAND STRUCTURE

■ [no] snmp-server
view < Operator | Manager > -- Add/delete SNMP community
■
write-access
■
■ snmp-server
■ [no] snmp-server
traps -- Enable/disable event traps to be sent by the switch
■
arp-protect
■
auth-server-fail
■
dhcp-snooping
■
dyn-ip-lockdown
■
link-change
■
login-failure-mgr
■
password-change-mgr
■
port-security
■
snmp-authentication
■
620)
extended
■
standard
■
■ [no] snmp-server
address
■
community
■
events
■
© 2009 Hewlett-Packard Development Company, L.P.
community -- Add/delete SNMP community (ASCII-STR)
< Restricted | Unrestricted | | ... > -- Add/delete SNMP community
contact -- Name of the switch administrator. (ASCII-STR)
enable -- Enable/Disable SNMPv1/v2
-- Traps for Dynamic ARP Protection.
-- Traps reporting authentication server unreachable.
-- Traps for DHCP-Snooping.
-- Traps for Dynamic Ip Lockdown
-- Traps for link-up and link-down. ([ethernet] PORT-LIST)
-- Traps for management interface login failure.
-- Traps for management interface password change.
-- Traps for port access authentication failure.
-- Select RFC-1157 (standard) or HP-ICF-SNMP (extended) traps.
-- Send traps for Extended Authentication failures.
-- Send traps for Standard Authentication failures.
host -- Define SNMP traps and their receivers
-- IP address of SNMP notification host. (IP-ADDR)
-- Name of the SNMP community (up to 32 characters). (ASCII-STR)
< None | Debug | All | ... > --
(p. 616)
(p. 621)
(p. 615)
(p. 616)
(p. 616)
(p. 617)
(p. 614)
(p. 616)
snmp-server
(p. 615)
(p. 622)
(p. 622)
(p. 616)
(p. 615)
(p. 618)
(p. 619)
(p. 619)
(p. 619)
(p. 617)
(p. 620)
(p. 615)
(p.
613