HP ProCurve 5400zl Reference Manual page 100

Command Line Interface Reference Guide
xmodem
■
■ copy crash-log
card -- Enter single slot identifier. (SLOT-ID-RANGE)
■
tftp -- Copy data to a TFTP server.
■
tftp-ip
■
■
tftp-ipv6
■
■
usb -- Copy data to a USB flash drive.
■
filename
■
xmodem
■
mm -- Copy from the management card.
■
tftp -- Copy data to a TFTP server.
■
tftp-ip
■
■
tftp-ipv6
■
■
usb -- Copy data to a USB flash drive.
■
filename
■
xmodem
■
tftp -- Copy data to a TFTP server.
■
tftp-ip
■
filename
■
tftp-ipv6
■
filename
■
usb -- Copy data to a USB flash drive.
■
filename
■
xmodem
■
■ copy event-log
tftp -- Copy data to a TFTP server.
■
tftp-ip
■
filename
■
■
■
tftp-ipv6
■
filename
■
■
■
usb -- Copy data to a USB flash drive.
■
filename
■
xmodem
■
pc -- Change CR/LF to PC style.
■
unix
■
■ copy flash
flash < primary | secondary > -- Copy to primary/secondary flash.
■
tftp -- Copy data to a TFTP server.
■
tftp-ip
■
filename
■
■
tftp-ipv6
■
filename
■
■
usb -- Copy data to a USB flash drive.
■
© 2009 Hewlett-Packard Development Company, L.P.
-- Use xmodem on the terminal as the data destination.
-- Copy the switch log file.
-- Specify TFTP server IPv4 address. (IP-ADDR)
filename -- Specify filename for the TFTP transfer. (ASCII-STR)
-- Specify TFTP server IPv6 address. (IPV6-ADDR)
filename -- Specify filename for the TFTP transfer. (ASCII-STR)
-- Specify filename for the USB transfer. (ASCII-STR)
-- Use xmodem on the terminal as the data destination.
-- Specify TFTP server IPv4 address. (IP-ADDR)
filename -- Specify filename for the TFTP transfer. (ASCII-STR)
-- Specify TFTP server IPv6 address. (IPV6-ADDR)
filename -- Specify filename for the TFTP transfer. (ASCII-STR)
-- Specify filename for the USB transfer. (ASCII-STR)
-- Use xmodem on the terminal as the data destination.
-- Specify TFTP server IPv4 address. (IP-ADDR)
-- Specify filename for the TFTP transfer. (ASCII-STR)
-- Specify TFTP server IPv6 address. (IPV6-ADDR)
-- Specify filename for the TFTP transfer. (ASCII-STR)
-- Specify filename for the USB transfer. (ASCII-STR)
-- Use xmodem on the terminal as the data destination.
-- Copy event log file.
-- Specify TFTP server IPv4 address. (IP-ADDR)
-- Specify filename for the TFTP transfer. (ASCII-STR)
pc -- Change CR/LF to PC style.
unix -- Change CR/LF to unix style.
-- Specify TFTP server IPv6 address. (IPV6-ADDR)
-- Specify filename for the TFTP transfer. (ASCII-STR)
pc -- Change CR/LF to PC style.
unix -- Change CR/LF to unix style.
-- Specify filename for the USB transfer. (ASCII-STR)
-- Use xmodem on the terminal as the data destination.
-- Change CR/LF to unix style.
-- Copy the switch system image file.
-- Specify TFTP server IPv4 address. (IP-ADDR)
-- Specify filename for the TFTP transfer. (ASCII-STR)
cv_out_flash < primary | secondary > -- Copy from primary/secondary flash.
-- Specify TFTP server IPv6 address. (IPV6-ADDR)
-- Specify filename for the TFTP transfer. (ASCII-STR)
cv_out_flash < primary | secondary > -- Copy from primary/secondary flash.
(p. 107)
(p. 105)
(p. 124)
(p. 133)
(p. 119)
(p. 124)
(p. 133)
(p. 124)
(p. 133)
(p. 109)
(p. 124)
(p. 120)
(p. 131)
(p. 120)
(p. 131)
(p. 133)
(p. 120)
(p. 131)
(p. 116)
(p. 124)
(p. 133)
(p. 135)
(p. 126)
(p. 109)
(p. 129)
(p. 109)
(p. 109)
(p. 135)
(p. 126)
(p. 109)
(p. 129)
(p. 109)
(p. 109)
(p. 135)
(p. 126)
(p. 109)
(p. 129)
(p. 109)
(p. 109)
(p. 135)
(p. 126)
(p. 109)
(p. 129)
(p. 109)
(p. 109)
(p. 135)
(p. 116)
(p. 126)
(p. 109)
(p. 129)
(p. 109)
copy
(p. 108)
(p. 108)
98