YASKAWA SGM7D-30F Product Manual page 455

4.4 Command Option Attachable-type FT82 SERVOPACKs with INDEXER Modules
Parameter
No.
Pn531
Pn533
Pn534
Pn535
Pn536
Pn550
Pn551
Pn552
Pn553
Pn55A
Pn560
Pn561
Pn600
Pn601
Pn603
Pn604
Pn61A
Pn61B
*15
Pn61C
*15
Pn61D
*15
4-130
Name
Program Jogging Travel
2
Distance
Program Jogging Move-
2
ment Speed
Program Jogging Accel-
2 eration/Deceleration
Time
Program Jogging Wait-
2
ing Time
Program Jogging Num-
2
ber of Movements
Analog Monitor 1 Offset
2
Voltage
Analog Monitor 2 Offset
2
Voltage
Analog Monitor 1 Mag-
2
nification
Analog Monitor 2 Mag-
2
nification
Power Consumption
2
Monitor Unit Time
Residual Vibration
2
Detection Width
Overshoot Detection
2
Level
Regenerative Resistor
2
*11
Capacity
Dynamic Brake Resis-
2 tor Allowable Energy
Consumption
Regenerative Resis-
2
tance
Dynamic Brake Resis-
2
tance
Overheat Protection
2
Selections
n.  X
Overheat Protection Selection
0 Disable overheat protection.
1
Use overheat protection in the Yaskawa Linear Servomotor.
Monitor a negative voltage input from a sensor attached to the machine and
2
use overheat protection.
Monitor a positive voltage input from a sensor attached to the machine and
3
use overheat protection.
n.  X 
Reserved parameter (Do not change.)
n.  X 
Reserved parameter (Do not change.)
n.X 
Reserved parameter (Do not change.)
2 Overheat Alarm Level
2 Overheat Warning Level
Overheat Alarm Filter
2
Time
Setting Setting Default
Range Unit Setting
1 refer-
1 to
ence 32768
1,073,741,824
unit
Rotary:
-1
1 min
Direct
1 to 10,000 500
Drive:
0.1
-1
min
2 to 10,000 1 ms 100
0 to 10,000 1 ms 100
0 to 1,000 Times 1
-10,000 to
0.1 V 0
10,000
-10,000 to
0.1 V 0
10,000
-10,000 to
× 0.01
100
10,000
-10,000 to
× 0.01
100
10,000
1 to 1,440 1 min 1
1 to 3,000 0.1% 400
0 to 100 1% 100
Depends on
10 W 0
*12
model.
0 to 65,535 10 J 0
0 to 65,535 10 mΩ 0
0 to 65,535 10 mΩ 0
0000h to
– 0000h
0003h
0 to 500 0.01 V 250
0 to 100 1% 100
0 to 65,535 1 s 0
Continued from previous page.
Applicable When Classi-
Motors Enabled fication
Immedi-
All Setup
ately
Immedi-
Rotary Setup
ately
Immedi-
All Setup
ately
Immedi-
All Setup
ately
Immedi-
All Setup
ately
Immedi-
All Setup
ately
Immedi-
All Setup
ately
Immedi-
All Setup
ately
Immedi-
All Setup
ately
Immedi-
All Setup
ately
Immedi-
All Setup
ately
Immedi-
All Setup
ately
Immedi-
All Setup
ately
After
All Setup
restart
Immedi-
All Setup
ately
After
All Setup
restart
After
Linear Setup
restart
*14
Immedi-
All Setup
ately
Immedi-
All Setup
ately
Immedi-
All Setup
ately
Continued on next page.
Refer-
ence
*1
*1
*1
*1
*1
*1
*1
*1
*1
−
*1
*1
*1
*13
*1
*13
*1
*1
*1
*1