Huawei Quidway S3500 Series Operation Manual page 161

Operation Manual - Routing Protocol
Quidway S3500 Series Ethernet Switches
3.3 Displaying and Debugging RIP........................................................................................ 3-11
3.4 Typical RIP Configuration Example ................................................................................. 3-11
3.4.1 Networking requirements ...................................................................................... 3-11
3.4.2 Networking diagram .............................................................................................. 3-12
3.4.3 Configuration procedure........................................................................................ 3-12
3.5 RIP Fault Diagnosis and Troubleshooting ....................................................................... 3-13
Chapter 4 OSPF Configuration .................................................................................................... 4-1
4.1 OSPF Overview ................................................................................................................. 4-1
4.1.1 Introduction to OSPF............................................................................................... 4-1
4.1.2 Process of OSPF Route Calculation ....................................................................... 4-1
4.1.3 OSPF Packets......................................................................................................... 4-2
4.1.4 Basic Concepts Related to OSPF ........................................................................... 4-3
4.2 OSPF Configuration........................................................................................................... 4-4
4.2.1 Enabling OSPF and Enter OSPF View ................................................................... 4-5
4.2.2 Entering OSPF Area view ....................................................................................... 4-5
4.2.3 Specifying interface................................................................................................. 4-6
4.2.4 Configuring Router ID ............................................................................................. 4-6
4.2.5 Configuring the Network Type on the OSPF Interface............................................ 4-7
4.2.6 Configuring the Cost for Sending Packets on an Interface..................................... 4-8
4.2.7 Setting the Interface Priority for DR Election .......................................................... 4-8
4.2.8 Setting the Peer....................................................................................................... 4-9
4.2.9 Setting the Interval of Hello Packet Transmission ................................................ 4-10
4.2.10 Setting a dead timer for the neighboring routers................................................. 4-10
4.2.11 Configuring an Interval required for sending LSU packets ................................. 4-11
4.2.12 Setting an Interval for LSA Retransmission between Neighboring Routers ....... 4-11
4.2.13 Setting a Shortest Path First (SPF) Calculation Interval for OSPF..................... 4-12
4.2.14 Configuring STUB Area of OSPF........................................................................ 4-12
4.2.15 Configuring NSSA of OSPF ................................................................................ 4-13
4.2.16 Configuring the Route Summarization of OSPF Area......................................... 4-15
4.2.17 Configuring Summarization of Imported Routes by OSPF ................................. 4-15
4.2.18 Configuring OSPF Virtual Link ............................................................................ 4-16
4.2.19 Configuring the OSPF Area to Support Packet Authentication........................... 4-17
4.2.20 Configuring OSPF Packet Authentication ........................................................... 4-17
4.2.21 Configure OSPF to import Routes of Other Protocols ........................................ 4-18
4.2.22 Configuring Parameters for OSPF to Import External Routes ............................ 4-19
4.2.23 Configuring OSPF to Import the Default Route................................................... 4-20
4.2.24 Setting OSPF Route Preference ......................................................................... 4-20
4.2.25 Configuring OSPF Route Filtering....................................................................... 4-21
4.2.26 Configuring to Fill the MTU Field When an Interface Transmits DD Packets ..... 4-22
4.2.27 Disabling the Interface to Send OSPF Packets .................................................. 4-22
4.2.28 Configuring OSPF and Network Management System (NMS) ........................... 4-23
4.2.29 Resetting the OSPF Process .............................................................................. 4-24
Huawei Technologies Proprietary
ii
Table of Contents