YASKAWA GA800 Programming Manual page 74

1.10 H: Terminal Functions
No.
Name
(Hex.)
H3-07 Terminal A3 Gain Setting
(0415)
RUN
H3-08 Terminal A3 Bias Setting
(0416)
RUN
H3-09 Terminal A2 Signal Level
Select
(0417)
H3-10 Terminal A2 Function
Selection
(0418)
H3-11 Terminal A2 Gain Setting
(0419)
RUN
H3-12 Terminal A2 Bias Setting
(041A)
RUN
H3-13 Analog Input FilterTime
Constant
(041B)
H3-14 Analog Input Terminal
Enable Sel
(041C)
H3-16 Terminal A1 Offset
(02F0)
H3-17 Terminal A2 Offset
(02F1)
H3-18 Terminal A3 Offset
(02F2)
H3-40 Mbus Reg 15C1h Input
Function
(0B5C)
H3-41 Mbus Reg 15C2h Input
Function
(0B5F)
H3-42 Mbus Reg 15C3h Input
Function
(0B62)
H3-43 Mbus Reg Inputs
FilterTime Const
(117F)
■
H3-xx: MFAI Setting Values
Setting Value Function
0 Frequency Reference
1 Frequency Gain
74
V/f CL-V/f OLV CLV AOLV
Sets the gain of the analog signal input to MFAI terminal A3.
V/f CL-V/f OLV CLV AOLV
Sets the bias of the analog signal input to MFAI terminal A3.
V/f CL-V/f OLV CLV AOLV
Sets the input signal level for MFAI terminal A2.
0 : 0-10V (LowLim=0)
1 : -10 to +10V (Bipolar Reference)
2 : 4 to 20 mA
3 : 0 to 20 mA
V/f CL-V/f OLV CLV AOLV
Sets the function for MFAI terminal A2.
V/f CL-V/f OLV CLV AOLV
Sets the gain of the analog signal input to MFAI terminal A2.
V/f CL-V/f OLV CLV AOLV
Sets the bias of the analog signal input to MFAI terminal A2.
V/f CL-V/f OLV CLV AOLV
Sets the time constant for primary delay filters on MFAI terminals.
V/f CL-V/f OLV CLV AOLV
Sets the enabled terminal or terminals when H1-xx = C [MFDI Function Select = Analog
Terminal Enable Selection] is ON.
1 : Terminal A1 only
2 : Terminal A2 only
3 : Terminals A1 and A2
4 : Terminal A3 only
5 : Terminals A1 and A3
6 : Terminals A2 and A3
7 : Terminals A1, A2, and A3
V/f CL-V/f OLV CLV AOLV
Sets the offset level for analog signals input to terminal A1. Usually it is not necessary to
change this setting.
V/f CL-V/f OLV CLV AOLV
Sets the offset level for analog signals input to terminal A2. Usually it is not necessary to
change this setting.
V/f CL-V/f OLV CLV AOLV
Sets the offset level for analog signals input to terminal A3. Usually it is not necessary to
change this setting.
V/f CL-V/f OLV CLV AOLV
Sets the MEMOBUS AI1 function.
V/f CL-V/f OLV CLV AOLV
Sets the MEMOBUS AI2 function.
V/f CL-V/f OLV CLV AOLV
Sets the MEMOBUS AI3 function.
V/f CL-V/f OLV CLV AOLV
Sets the time constant to apply a primary delay filter to the MEMOBUS analog input
terminal.
V/f CL-V/f OLV CLV AOLV
The input value from the MFAI terminal set with this function becomes the master frequency reference.
V/f CL-V/f OLV CLV AOLV
The drive multiplies the analog frequency reference with the input value from the MFAI set with this function.
Description
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
YASKAWA TOEPYAIGA8002B GA800 Drive Programming
Default
Ref.
(Range)
100.0% 410
(-999.9 - +999.9%)
0.0% 410
(-999.9 - +999.9%)
2 410
(0 - 3)
0 410
(0 - 32)
100.0% 411
(-999.9 - +999.9%)
0.0% 411
(-999.9 - +999.9%)
0.03 s 411
(0.00 - 2.00 s)
7 411
(1 - 7)
0 412
(-500 - +500)
0 412
(-500 - +500)
0 412
(-500 - +500)
F 412
(4 - 2F)
F 412
(4 - 2F)
F 413
(4 - 2F)
0.00 s 413
(0.00 - 2.00 s)
Ref.
413
413