YASKAWA GA800 Programming Manual page 641

Motor Code Selection.............................................. 311
Motor Parameters................................................... 310
Positive Temperature Coefficient (PTC) Thermistor............... 435
Protection Functions
DC bus undervoltage............................................... 449
Drive Overheating.................................................. 475
LF2 ................................................................... 479
Motor Overload..................................................... 436
oC..................................................................... 479
oH2 ................................................................... 475
Overcurrent.......................................................... 479
Uv1 ................................................................... 449
Protective function
Desynchronization.................................................. 483
Drive Overheating.................................................. 475
GF .................................................................... 477
Ground Fault Detection............................................ 477
HCA .................................................................. 481
Input Phase Detection.............................................. 476
Internal Drive Braking Transistor ................................ 482
LF..................................................................... 477
Low Speed Desynchronization ................................... 483
LSo ................................................................... 483
Motor Overheating ................................................. 440
Motor Overheating (PTC Input).................................. 440
oH..................................................................... 475
oH3 ................................................................... 440
oH4 ................................................................... 440
oL2 ................................................................... 478
Output Current Overload .......................................... 481
Output Phase Loss Detection ..................................... 477
Overload ............................................................. 478
PF ..................................................................... 476
rr ...................................................................... 482
Software Current Limit Selection ................................ 478
Pulse Train Input
Terminal RP Function Selection.................................. 427
Pulse Train Input/Output
Parameter ............................................................ 426
Pulse train output
Terminal MP function selection .................................. 429
Wiring specifications............................................... 632
R
Ready
LED status........................................................... 549
Remove
Front cover .......................................................... 612
Terminal cover ...................................................... 612
RESET key............................................................... 543
Restore
Parameters (Auto Backup) ........................................ 587
Parameters (keypad to drive) ..................................... 567
Reverse Operation Selection........................................... 200
RJ-45 connector ......................................................... 543
Rotational Auto-Tuning
Induction Motor .................................................... 589
PM Motors .......................................................... 590
Precautions .......................................................... 596
rr
Protective function ................................................. 482
RUN
LED status........................................................... 549
YASKAWA TOEPYAIGA8002B GA800 Drive Programming
Run command
LOCAL/REMOTE Run selection ................................ 196
Switching between LOCAL/REMOTE ......................... 196
Run Command at Power Up ........................................... 206
Run Command Selection 2
Switching between LOCAL/REMOTE ......................... 205
RUN indicator ..................................................... 543, 546
RUN key ................................................................. 543
S
S-curve characteristics
Parameter ............................................................ 252
Sampling time setting
Data log .............................................................. 584
Serial communication terminals
MEMOBUS/Modbus Communications ......................... 626
Set date and time
Operation ............................................................ 577
Set time
Operation ............................................................ 577
Setup Wizard
Operation ............................................................ 579
Short Circuit Braking
Parameter ............................................................ 207
Side-by-side
Derating.............................................................. 480
Simple Positioning Stop................................................ 287
Slip compensation
Parameter ............................................................ 253
Softcharge Relay Maintenance Set ................................... 524
Software Current Limit Selection
Protective function ................................................. 478
Software version
Display procedure .................................................. 586
Speed Agreement
Parameter ............................................................ 462
Speed Detection
Parameter ............................................................ 462
Speed Estimation Speed Search ....................................... 212
Speed limit
Parameter ............................................................ 288
Speed Search function
Operation during momentary power loss........................ 447
Parameter ............................................................ 210
Stall Prevention function
Parameter ............................................................ 452
Stationary Auto-Tuning
Induction Motor .................................................... 589
PM Motors .......................................................... 590
Precautions .......................................................... 596
Stationary Auto-Tuning for Line-to-Line Resistance .............. 589
Precautions .......................................................... 597
Stator resistance Auto-Tuning ......................................... 590
Precautions .......................................................... 597
Stop command
LOCAL/REMOTE Run selection ................................ 196
STOP key................................................................. 543
STOP Key Function Selection......................................... 518
Stopping Method Selection ............................................ 197
T
Terminal block........................................................... 626
Control circuit terminal block functions......................... 624
I/O terminals function selection switches ....................... 631
641