YASKAWA GA800 Programming Manual page 59

No.
Name
(Hex.)
F7-12 Gateway Address 4
(03F0)
F7-13 Address Mode at Startup
(03F1)
F7-14 Duplex Mode Selection
(03F2)
F7-15 Communication Speed
Selection
(03F3)
F7-16 Timeout Value
(03F4)
F7-17 EtherNet/IP Speed
Scaling Factor
(03F5)
F7-18 EtherNet/IP Current Scale
Factor
(03F6)
F7-19 EtherNet/IP Torque Scale
Factor
(03F7)
F7-20 EtherNet/IP Power
Scaling Factor
(03F8)
F7-21 EtherNet/IP Voltage Scale
Factor
(03F9)
F7-22 EtherNet/IP Time Scaling
(03FA)
F7-23 - F7-27 Dynamic Out Param 1 to
10 for CommCard
(03FB - 03FF)
F7-28- F7-32
(0370 - 0374)
F7-33 - F7-42 Dynamic In Param 1 to
10 for CommCard
(0375 - 037E)
F7-60 PZD1 Write (Control
Word)
(0780)
YASKAWA TOEPYAIGA8002B GA800 Drive Programming
Description
V/f CL-V/f OLV CLV AOLV
Sets the fourth octet of the gateway address of the connected network.
Note:
Set this parameter when F7-13 = 0 [Address Mode at Startup = Static].
V/f CL-V/f OLV CLV AOLV
Sets the method to set option card IP addresses.
0 : Static
1 : BOOTP
2 : DHCP
Note:
• The following setting values are available when using the PROFINET
communication option card (SI-EP3).
–0: Static
–2: DHCP
• When F7-13 = 0, set parameters F7-01 to F7-12 [IP Address 1 to Gateway Address
4] to set the IP Address. Be sure to set a different IP address for each drive on the
network.
V/f CL-V/f OLV CLV AOLV
Sets the duplex mode setting method.
0 : Half/Half
1 : Auto/Auto
2 : Full/Full
3 : Half/Auto
4 : Half/Full
5 : Auto/Half
6 : Auto/Full
7 : Full/Half
8 : Full/Auto
V/f CL-V/f OLV CLV AOLV
Sets the communications speed.
10 : 10/10 Mbps
100 : 100/100 Mbps
101 : 10/100 Mbps
102 : 100/10 Mbps
V/f CL-V/f OLV CLV AOLV
Sets the detection time for a communications timeout.
Note:
Set this parameter to 0.0 to disable the connection timeout function.
V/f CL-V/f OLV CLV AOLV
Sets the scaling factor for the speed monitor in the EtherNet/IP Class ID 2AH Object.
V/f CL-V/f OLV CLV AOLV
Sets the scaling factor for the output current monitor in the EtherNet/IP Class ID 2AH
Object.
V/f CL-V/f OLV CLV AOLV
Sets the scaling factor for the torque monitor in the EtherNet/IP Class ID 2AH Object.
V/f CL-V/f OLV CLV AOLV
Sets the scaling factor for the power monitor in the EtherNet/IP Class ID 2AH Object.
V/f CL-V/f OLV CLV AOLV
Sets the scaling factor for the voltage monitor in the EtherNet/IP Class ID 2AH Object.
V/f CL-V/f OLV CLV AOLV
Sets the scaling factor for the time monitor in the EtherNet/IP Class ID 2AH Object.
V/f CL-V/f OLV CLV AOLV
Sets Output Assembly 116. The drive writes the values from Output Assembly 116 to the
MEMOBUS/Modbus address register that is stored for each parameter. The drive will not
write the values from Output Assembly 116 to the registers when the MEMOBUS/Modbus
address is 0.
V/f CL-V/f OLV CLV AOLV
Sets Input Assembly 166. The drive sends the values from the MEMOBUS/Modbus
address registers stored for each parameter to Input Assembly 166. The drive returns the
default register value for the option card when the MEMOBUS/Modbus address is 0 and
the value sent to Input Assembly 166 is not defined.
V/f CL-V/f OLV CLV AOLV
Sets the MEMOBUS/Modbus address for PZD1 (PPO output). PZD1 (PPO output)
functions as the STW when F7-60 = 0, 1, or 2.
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
1.9 F: Options
Default
Ref.
(Range)
1 352
(0 - 255)
2 352
(0 - 2)
1 352
(0 - 8)
10 352
(10, 100 - 102)
0.0 s 353
(0.0 - 30.0 s)
0 353
(-15 - +15)
0 353
(-15 - +15)
0 353
(-15 - +15)
0 353
(-15 - +15)
0 353
(-15 - +15)
0 353
(-15 - +15)
0 354
0 354
0 354
59
1