YASKAWA GA800 Programming Manual page 62

1.10 H: Terminal Functions
■
H1-xx: MFDI Setting Values
Setting Value Function
0 3-Wire Sequence
1 LOCAL/REMOTE
Selection
2 External Reference 1/2
Selection
3 Multi-Step Speed
Reference 1
4 Multi-Step Speed
Reference 2
5 Multi-Step Speed
Reference 3
6 Jog Reference Selection
7 Accel/Decel Time
Selection 1
8 Baseblock Command (N.
O.)
9 Baseblock Command (N.
C.)
A Accel/Decel Ramp Hold
B Overheat Alarm (oH2)
C Analog Terminal Enable
Selection
D Ignore Speed Fdbk (V/f
w/o Enc)
E ASR Integral Reset
F Not Used
10 Up Command
62
V/f CL-V/f OLV CLV AOLV
Sets the direction of motor rotation for 3-wire sequence.
V/f CL-V/f OLV CLV AOLV
Sets drive control for the keypad (LOCAL) or an external source (REMOTE).
ON : LOCAL
OFF : REMOTE
V/f CL-V/f OLV CLV AOLV
Sets the drive to use Run command source 1/2 or Reference command source 1/2 when in REMOTE Mode.
ON : b1-15 = [Frequency Reference Selection 2], b1-16 [Run Command Selection 2]
OFF : b1-01 = [Frequency Reference Selection 1], b1-02 [Run Command Selection 1]
V/f CL-V/f OLV CLV AOLV
Uses speed references d1-01 to d1-16 to set a multi-step speed reference.
V/f CL-V/f OLV CLV AOLV
Uses speed references d1-01 to d1-16 to set a multi-step speed reference.
V/f CL-V/f OLV CLV AOLV
Uses speed references d1-01 to d1-16 to set a multi-step speed reference.
V/f CL-V/f OLV CLV AOLV
Sets the drive to use the JOG Frequency Reference (JOG command) set in d1-17. The JOG Frequency Reference (JOG
command) overrides Frequency References 1 to 16 (d1-01 to d1-16).
V/f CL-V/f OLV CLV AOLV
Sets the drive to use Acceleration/Deceleration Time 1 [C1-01, C1-02] or Acceleration/Deceleration Time 2 [C1-03,
C1-04].
V/f CL-V/f OLV CLV AOLV
Sets the command that stops drive output and coasts the motor to stop when the input is ON.
ON : Baseblock (drive output stop)
OFF : Normal operation
V/f CL-V/f OLV CLV AOLV
Sets the command that stops drive output and coasts the motor to stop when the input terminal is OFF.
ON : Normal operation
OFF : Baseblock (drive output stop)
V/f CL-V/f OLV CLV AOLV
Momentarily pauses motor acceleration and deceleration when the terminal is turned ON, retains the output frequency
that was stored in the drive at the time of the pause, and restarts motor operation.
V/f CL-V/f OLV CLV AOLV
Sets the drive to display an oH2 [Drive Overheat Warning] alarm when the input terminal is ON. The alarm does not
have an effect on drive operation.
V/f CL-V/f OLV CLV AOLV
Sets the command that enables or disables the terminals selected in H3-14 [Analog Input Terminal Enable Sel].
ON : Input to the terminal selected with H3-14 is enabled
OFF : Input to the terminal selected with H3-14 is disabled
V/f CL-V/f OLV CLV AOLV
Sets the command to disable speed feedback control and run the drive in V/f control or use speed feedback from the
encoder.
ON : Speed feedback control disable (V/f Control)
OFF : Speed feedback control enable (Closed Loop V/f Control)
V/f CL-V/f OLV CLV AOLV
Sets the command to reset the integral value and use PI control or P control for the speed control loop.
ON : P control
OFF : PI control
V/f CL-V/f OLV CLV AOLV
Use this setting for unused terminals or to use terminals in through mode.
V/f CL-V/f OLV CLV AOLV
Sets the command to use a push button switch to increase the drive frequency reference. You must also set Setting 11
[Down Command].
ON : Increases the frequency reference.
OFF : Holds the current frequency reference.
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
YASKAWA TOEPYAIGA8002B GA800 Drive Programming
Ref.
361
362
362
362
363
363
363
363
363
364
364
364
364
364
364
365
365