Lucent DDM-2000 OC-3 User And Service Manual page 816

DLP-512
: Detailed Level Procedure
Page 6 of 10
Table A – DDM-2000 OC-3 Parameters Provisionable Via the CIT (Contd)
Parameter
VT1.5 path signal
degrade threshold***
NSA VT path AIS
SA VT path AIS
VT channel state***
DS3 VMR mode†
Clear channel DS3 AIS insertion†¶¶
DS3 sig failure alm. level†
DS3 AIS failure alm. level¶¶¶
DS3 failure threshold†
DS3 PM mode†
DS3 PM frame†
DS3 PM format†
DS3 X-bits¶¶¶
DS3 port state†
DS1 line coding†
DS1 alarm level†
DS1 failure threshold†
DS1 BPV to LOS†
DS1 AIS insertion†
DS1 PM Mode†
DS1 PM Format†
DS1 primary port state†
Environmental alarm level
Environmental alarm type
Environmental alarm description
Control point description
Far end communication over DCC**
DCC identity for OSI ntwks.
Lanreset
Porttype
Baudrate
Echo
CIT/DCC security**
CIT/DCC timeout (minutes)**
SYNC mode switching
Sync Timing Source††‡‡
Sync Output Mode§§
AIS Threshold
Auto. sync. reconfig.
EC-1 alarm level†
EC-1 degrade threshold†
EC-1 port state†
See notes and footnotes at end of table.
Range
-5 -9
10 to 10
MN, NR
MJ, MN, NA, NR
NMON, AUTO‡
VMR, VM, clear channel
yes, no
CR, MJ, MN, NA
CR, MJ, MN, NA
-3 -6
10 , 10 BER
off, on
m13, cbit
pbit, fmbit, cpbit
1,0
NMON, AUTO‡
AMI,B8ZS,noOverride§
MJ, MN, NA
-3 -6 -7
10 , 10 , 10 , 10
yes,no
yes, no
off, on
sf, esf, esfn
NMON, AUTO‡
CR, MJ, MN, NA
10 characters
26 characters
26 characters
enabled,disabled
userside, networkside
y,n
cit,tl1
synch,asynch
1200,2400,4800,9600,19200
enabled,disenabled
enabled,disabled,lockout
0-120
revertive, nonrevertive
main-1, main-2, fn-c
¶ track, lock1, lock2
level 5, level 4, level 3. level 2
enabled, disabled
CR, MJ, MN, NA
-5 -9
10 to 10 BER
NMON, AUTO‡
DDM-2000 OC-3 M
Issue 2, February 2000
Default
(Note 1)
-6
10
MN
MJ for ring
MN for linear
AUTO
VMR
no
CR
CR
-3
10
on
m13
pbit
1
AUTO
noOverride
NA
-8 -3
BER 10
no
yes
off
esf
AUTO
MN
enabled
see command pgs.
n
cit
synch
9600
enabled
disabled
15
revertive
main-1
track
level 5
disabled
CR
-6
10
AUTO
ULTIPLEXER
363-206-285
Command (Note 2)
set-vt1
set-vt1
set-vt1
set-state-vt1
set-t3†
set-t3†
set-t3†
set-t3†
set-t3†
set-t3†
set-t3†
set-t3†
set-t3†
set-state-t3†
set-t1†
set-t1†
set-t1†
set-t1†
set-t1†
set-t1
set-t1
set-state-t1†
set-attr-env
set-attr-env
set-attr-env
set-attr-cont
set-fecom**
set-fecom**
set-fecom**
set-secu**
set-secu**
set-secu**
set-secu**
set-secu**
set-sync
set-sync
set-sync
set-sync
set-sync
set-ec1
set-ec1
set-state-ec1