Huawei NetEngine80E Configuration Manual - Reliability page 77

HUAWEI NetEngine80E/40E Router
Configuration Guide - Reliability
Step 6 Configure the encapsulation protocol on the serial interface as TDM.
1.
2.
Step 7 Configuring PWs.
1.
2.
Step 8 Verify the configuration.
Simulate a fault on the side of PE2 connecting to the BSC.
# Run the shutdown command on CPOS3/0/1.
[PE2] controller cpos 3/0/1
[PE2-Cpos3/0/1] shutdown
Run the display aps group 1 command on PE2. The APS status changes to Switch. Run the
display cpos-trunk 1 command to view the CPOS-Trunk member interface status. CPOS 3/0/2
becomes Active.
[PE2] display aps group 1
APS Group
Issue 02 (2014-09-30)
[PE2] interface cpos-trunk 1
[PE2-Cpos-trunk1] t1 1 channel-set 1 timeslot-list 0-23
[PE2-Cpos-trunk1] t1 2 channel-set 2 timeslot-list 0-23
Configure PE1.
[PE1] interface serial2/0/1:0
[PE1-Serial2/0/1:0] link-protocol tdm
[PE1-Serial2/0/1:0] quit
[PE1] interface serial2/0/2:0
[PE1-Serial2/0/2:0] link-protocol tdm
[PE1-Serial2/0/2:0] quit
Configure PE2.
[PE2] interface trunk-serial1/1:0
[PE2-Trunk-Serial1/1:0] link-protocol tdm
[PE2-Trunk-Serial1/1:0] quit
[PE2] interface trunk-serial1/2:0
[PE2-Trunk-Serial1/2:0] link-protocol tdm
[PE2-Trunk-Serial1/2:0] quit
Configure PE1.
[PE1] pw-template 1to3
[PE1-pw-template-1to3] peer-address 192.3.3.3
[PE1-pw-template-1to3] jitter-buffer depth 20
[PE1-pw-template-1to3] tdm-encapsulation-number 40
[PE1-pw-template-1to3] quit
[PE1] interface serial2/0/1:0
[PE1-Serial2/0/1:0] mpls l2vc pw-template 1to3 100
[PE1] interface serial2/0/2:0
[PE1-Serial2/0/2:0] mpls l2vc pw-template 1to3 200
Configure PE2.
[PE2] pw-template 3to1
[PE2-pw-template-3to1] peer-address 192.2.2.2
[PE2-pw-template-3to1] jitter-buffer depth 20
[PE2-pw-template-3to1] tdm-encapsulation-number 40
[PE2-pw-template-3to1] quit
[PE2] interface trunk-serial1/1:0
[PE2-Trunk-Serial1/1:0] mpls l2vc pw-template 3to1 100
[PE2-Trunk-Serial1/1:0] undo shutdown
[PE2-Trunk-Serial1/1:0] quit
[PE2] interface trunk-serial1/2:0
[PE2-Trunk-Serial1/2:0] mpls l2vc pw-template 3to1 200
[PE2-Trunk-Serial1/2:0] undo shutdown
[PE2-Trunk-Serial1/2:0] quit
1: Cpos 3/0/1 working channel 1(Inactive)
Cpos3/0/2 protection channel 0(Active)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3 APS Configuration
60