Huawei NetEngine80E Configuration Manual - Reliability page 831

HUAWEI NetEngine80E/40E Router
Configuration Guide - Reliability
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
--------------------------------------------------------------------------------
Average Local-loss
Maximum Local-loss
Minimum Local-loss
Average Remote-loss :
Maximum Remote-loss :
Minimum Remote-loss :
Configuring the ETH-Test Function for a VLAN
The ETH-test function is short for Ethernet test signal. ETH-test instances are performed for a
unidirectional on-demand service or during an on-demand-service interruption to calculate
parameters, including the maximum bandwidth, frame loss ratio, and bit error rate.
Context
In Figure
AC interface of PE2. MEP1 initiates an ETH-test and sends test packets with a specified size
and code type at a specified rate and interval. Then check the number of packets MEP1 sends
and the number of packets MEP2 receives. If MEP1 sends more packets than MEP2 receives,
some packets have been dropped. Then MEP1 is configured to use the bisection method to
Issue 02 (2014-09-30)
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
1000 1000 1000
:
:
:
8-61, MEP1 is configured on an AC interface of PE1, and MEP2 is configured on an
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 Average Local-loss Ratio
0 Maximum Local-loss Ratio
0 Minimum Local-loss Ratio
0 Average Remote-loss Ratio :
0 Maximum Remote-loss Ratio :
0 Minimum Remote-loss Ratio :
8 Ethernet OAM Configuration
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
0 0.0000% 0.0000%
: 0.0000%
: 0.0000%
: 0.0000%
0.0000%
0.0000%
0.0000%
814