Huawei NetEngine80E Configuration Manual - Reliability page 918

HUAWEI NetEngine80E/40E Router
Configuration Guide - Reliability
[PE1-md-md1-ma-ma1] mep ccm-send enable
[PE1-md-md1-ma-ma1] remote-mep mep-id 32
[PE1-md-md1-ma-ma1] remote-mep ccm-receive enable
[PE1-md-md1-ma-ma1] quit
[PE1-md-md1] quit
# Configure PE2.
[PE2] cfm md md1
[PE2-md-md1] ma ma1
[PE2-md-md1-ma-ma1] mep mep-id 32 interface gigabitEthernet1/0/1.1 inward
[PE2-md-md1-ma-ma1] mep ccm-send enable
[PE2-md-md1-ma-ma1] remote-mep mep-id 31
[PE2-md-md1-ma-ma1] remote-mep ccm-receive enable
[PE2-md-md1-ma-ma1] quit
[PE2-md-md1] quit
Step 4 Set the MEP type as outward on each CE.
# Configure CE1.
[CE1] cfm md md2
[CE1-md-md2] ma ma2
[CE1-md-md2-ma-ma2] mep mep-id 61 interface gigabitEthernet1/0/1 outward
[CE1-md-md2-ma-ma2] ccm-interval 10000
[CE1-md-md2-ma-ma2] mep ccm-send enable
[CE1-md-md2-ma-ma2] remote-mep mep-id 62
[CE1-md-md2-ma-ma2] remote-mep ccm-receive enable
[CE1-md-md2-ma-ma2] quit
[CE1-md-md2] quit
# Configure CE2.
[CE2] cfm md md2
[CE2-md-md2] ma ma2
[CE2-md-md2-ma-ma2] mep mep-id 62 interface gigabitEthernet1/0/1 outward
[CE2-md-md2-ma-ma2] ccm-interval 10000
[CE2-md-md2-ma-ma2] mep ccm-send enable
[CE2-md-md2-ma-ma2] remote-mep mep-id 61
[CE2-md-md2-ma-ma2] remote-mep ccm-receive enable
[CE2-md-md2-ma-ma2] quit
[CE2-md-md2] quit
Step 5 Configure the AIS function.
# Configure PE1.
[PE1] cfm md md1
[PE1-md-md1] ma ma1
[PE1-md-md1-ma-ma1] ais enable
[PE1-md-md1-ma-ma1] ais link-status interface gigabitEthernet1/0/2
[PE1-md-md1-ma-ma1] ais level 6
[PE1-md-md1-ma-ma1] ais interval 1
[PE1-md-md1-ma-ma1] ais vlan vid 10 mep 31
[PE1-md-md1] quit
# Configure PE2.
Issue 02 (2014-09-30)
NOTE
In VPLS networking, the configuration is the same as in the VLL networking. In VLAN networking, run
the following commands to set the MEP type as outward:
[PE1-md-md1-ma-ma1] mep mep-id 31 interface gigabitEthernet1/0/1 outward
NOTE
In VPLS networking, the configuration is the same as in the VLL networking. In VLAN networking, run
the following commands to set the MEP type as outward:
[PE2-md-md1-ma-ma1] mep mep-id 31 interface gigabitEthernet1/0/1 outward
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
8 Ethernet OAM Configuration
901