Huawei NetEngine80E Configuration Manual - Reliability page 611

HUAWEI NetEngine80E/40E Router
Configuration Guide - Reliability
After the preceding configurations, an LDP session can be set up between PE1 and PE2. Run
the display mpls ldp session command. You can view that the Status field is Operational in
the command output.
Take the display on PE1 as an example.
<PE1> display mpls ldp session
LDP Session(s) in Public Network
Codes: LAM(Label Advertisement Mode), SsnAge Unit(DDDD:HH:MM)
A '*' before a session means the session is being deleted.
------------------------------------------------------------------------------
PeerID
------------------------------------------------------------------------------
2.2.2.9:0
3.3.3.9:0
------------------------------------------------------------------------------
TOTAL: 2 session(s) Found.
Step 5 Enable MPLS L2VPN; create a VC link; configure the sub-interface for QinQ VLAN tag
termination.
# Configure PE1.
[PE1] mpls l2vpn
[PE1-l2vpn] quit
[PE1] interface gigabitethernet 2/0/0.1
[PE1-GigabitEthernet2/0/0.1] control-vid 1 qinq-termination
[PE1-GigabitEthernet2/0/0.1] qinq termination l2 symmetry
[PE1-GigabitEthernet2/0/0.1] qinq termination pe-vid 100 ce-vid 10
[PE1-GigabitEthernet2/0/0.1] mpls l2vc 3.3.3.9 101
[PE1-GigabitEthernet2/0/0.1] undo shutdown
[PE1-GigabitEthernet2/0/0.1] quit
# Configure PE2.
[PE2] mpls l2vpn
[PE2-l2vpn] quit
[PE2] interface gigabitethernet 2/0/0.1
[PE2-GigabitEthernet2/0/0.1] control-vid 1 qinq-termination
[PE2-GigabitEthernet2/0/0.1] qinq termination l2 symmetry
[PE2-GigabitEthernet2/0/0.1] qinq termination pe-vid 100 ce-vid 10
[PE2-GigabitEthernet2/0/0.1] mpls l2vc 1.1.1.9 101
[PE2-GigabitEthernet2/0/0.1] undo shutdown
[PE2-GigabitEthernet2/0/0.1] quit
Step 6 Configure basic Ethernet CFM functions on each PE.
# Configure PE1.
[PE1] cfm enable
[PE1] cfm version standard
[PE1] cfm md md1
[PE1-md-md1] ma ma1
[PE1-md-md1-ma-ma1] ccm-interval 30
[PE1-md-md1-ma-ma1] map mpls l2vc 101 tagged
[PE1-md-md1-ma-ma1] mep mep-id 1 interface gigabitethernet 2/0/0.1 pe-vid 100 ce-
vid 10 inward
[PE1-md-md1-ma-ma1] remote-mep mep-id 2
[PE1-md-md1-ma-ma1] mep ccm-send enable
[PE1-md-md1-ma-ma1] remote-mep ccm-receive enable
[PE1-md-md1-ma-ma1] quit
Issue 02 (2014-09-30)
Status
Operational DU
Operational DU
NOTE
When you run the qinq termination command on the same main interface, the ce-vid values must be
different if the pe-vid values of the two sub-interfaces are the same.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
LAM SsnRole SsnAge
Passive 0000:00:09
Passive 0000:00:03
8 Ethernet OAM Configuration
KASent/Rcv
37/37
13/13
594