Huawei NetEngine80E Configuration Manual - Reliability page 253
Hide thumbs
Also See for NetEngine80E:
- Configuration manual (1301 pages) ,
- Configuration manual - reliability (761 pages) ,
- Installation manual (169 pages)
Table of Contents
Advertisement
HUAWEI NetEngine80E/40E Router
Configuration Guide - Reliability
# Configure NPE2.
[NPE2] interface eth-trunk 1
[NPE2-Eth-Trunk1] mode user-termination
[NPE2-Eth-Trunk1] quit
[NPE2] interface eth-trunk 1.1
[NPE2-Eth-Trunk1.1] control-vid 1 qinq-termination
[NPE2-Eth-Trunk1.1] qinq termination pe-vid 10 ce-vid 1 to 100
[NPE2-Eth-Trunk1.1] ip address 10.1.1.253 24
[NPE2-Eth-Trunk1.1] arp broadcast enable
[NPE2-Eth-Trunk1.1] quit
[NPE2] interface gigabitethernet1/0/1
[NPE2-GigabitEthernet1/0/1] mode user-termination
[NPE2-GigabitEthernet1/0/1] undo shutdown
[NPE2-GigabitEthernet1/0/1] quit
[NPE2] interface gigabitethernet1/0/1.100
[NPE2-GigabitEthernet1/0/1.100] control-vid 100 qinq-termination
[NPE2-GigabitEthernet1/0/1.100] qinq termination pe-vid 10 ce-vid 101 to 200
[NPE2-GigabitEthernet1/0/1.100] ip address 10.100.1.253 24
[NPE2-GigabitEthernet1/0/1.100] arp broadcast enable
[NPE2-GigabitEthernet1/0/1.100] quit
[NPE2] interface gigabitethernet1/0/1.101
[NPE2-GigabitEthernet1/0/1.101] control-vid 101 qinq-termination
[NPE2-GigabitEthernet1/0/1.101] qinq termination pe-vid 10 ce-vid 201 to 300
[NPE2-GigabitEthernet1/0/1.101] ip address 10.101.1.253 24
[NPE2-GigabitEthernet1/0/1.101] arp broadcast enable
[NPE2-GigabitEthernet1/0/1.101] quit
[NPE2] interface gigabitethernet1/0/1.102
[NPE2-GigabitEthernet1/0/1.102] control-vid 102 qinq-termination
[NPE2-GigabitEthernet1/0/1.102] qinq termination pe-vid 10 ce-vid 301 to 400
[NPE2-GigabitEthernet1/0/1.102] ip address 10.102.1.253 24
[NPE2-GigabitEthernet1/0/1.102] arp broadcast enable
[NPE2-GigabitEthernet1/0/1.102] quit
[NPE2] interface gigabitethernet1/0/1.103
[NPE2-GigabitEthernet1/0/1.103] control-vid 103 qinq-termination
[NPE2-GigabitEthernet1/0/1.103] qinq termination pe-vid 10 ce-vid 401 to 500
[NPE2-GigabitEthernet1/0/1.103] ip address 10.103.1.253 24
[NPE2-GigabitEthernet1/0/1.103] arp broadcast enable
[NPE2-GigabitEthernet1/0/1.103] quit
# After completing the preceding configurations, ping the peer Eth-Trunk1.1 from Eth-Trunk1.1
on each NPE. The link between NPE1 and NPE2 is working properly. In the following examples,
NPE1 can ping NPE2.
The sub-interfaces where the mVRRP backup group is configured can ping each other.
[NPE1] ping 10.1.1.253
PING 10.1.1.253: 56
--- 10.1.1.253 ping statistics ---
Split horizon configured on the VPLS network prevents data transmission between interfaces
on NPEs. Therefore, the sub-interfaces where service VRRP backup groups are configured on
Issue 02 (2014-09-30)
NOTE
After the IP address is assigned to each QinQ termination sub-interface, running the arp broadcast
enable command is recommended. This command allows the sub-interfaces to ping each other.
data bytes, press CTRL_C to break
Reply from 10.1.1.253: bytes=56 Sequence=1 ttl=255 time=160 ms
Reply from 10.1.1.253: bytes=56 Sequence=2 ttl=255 time=90 ms
Reply from 10.1.1.253: bytes=56 Sequence=3 ttl=255 time=160 ms
Reply from 10.1.1.253: bytes=56 Sequence=4 ttl=255 time=180 ms
Reply from 10.1.1.253: bytes=56 Sequence=5 ttl=255 time=120 ms
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 90/142/180 ms
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
4 VRRP Configuration
236
Advertisement
Table of Contents
