Huawei NetEngine80E Configuration Manual - Reliability page 599

HUAWEI NetEngine80E/40E Router
Configuration Guide - Reliability
[PE3-vsi-ldp1-ldp] peer 1.1.1.1
[PE3-vsi-ldp1-ldp] peer 2.2.2.2
Step 6 Configure a sub-interface for QinQ VLAN tag termination on the AC interface of each PE and
bind the sub-interface to the VSI.
# Configure PE1.
[PE1] interface gigabitethernet 2/0/0.1
[PE1-GigabitEthernet2/0/0.1] control-vid 1 qinq-termination
[PE1-GigabitEthernet2/0/0.1] qinq termination l2 symmetry
[PE1-GigabitEthernet2/0/0.1] qinq termination pe-vid 100 ce-vid 10
[PE1-GigabitEthernet2/0/0.1] l2 binding vsi ldp1
[PE1-GigabitEthernet2/0/0.1] undo shutdown
[PE1-GigabitEthernet2/0/0.1] quit
# Configure PE2.
[PE2] interface gigabitethernet 2/0/0.1
[PE2-GigabitEthernet2/0/0.1] control-vid 1 qinq-termination
[PE2-GigabitEthernet2/0/0.1] qinq termination l2 symmetry
[PE2-GigabitEthernet2/0/0.1] qinq termination pe-vid 100 ce-vid 10
[PE2-GigabitEthernet2/0/0.1] l2 binding vsi ldp1
[PE2-GigabitEthernet2/0/0.1] undo shutdown
[PE2-GigabitEthernet2/0/0.1] quit
# Configure PE3.
[PE3] interface gigabitethernet 2/0/0.1
[PE3-GigabitEthernet2/0/0.1] control-vid 1 qinq-termination
[PE3-GigabitEthernet2/0/0.1] qinq termination l2 symmetry
[PE3-GigabitEthernet2/0/0.1] qinq termination pe-vid 100 ce-vid 10
[PE3-GigabitEthernet2/0/0.1] l2 binding vsi ldp1
[PE3-GigabitEthernet2/0/0.1] undo shutdown
[PE3-GigabitEthernet2/0/0.1] quit
Step 7 Configure basic Ethernet CFM functions on each PE.
# Configure PE1.
[PE1] cfm enable
[PE1] cfm version standard
[PE1] cfm md md1
[PE1-md-md1] ma ma1
[PE1-md-md1-ma-ma1] ccm-interval 30
[PE1-md-md1-ma-ma1] map vsi ldp1
[PE1-md-md1-ma-ma1] mep mep-id 1 interface gigabitethernet 2/0/0.1 pe-vid 100 ce-
vid 10 inward
[PE1-md-md1-ma-ma1] remote-mep mep-id 2
[PE1-md-md1-ma-ma1] remote-mep mep-id 3
[PE1-md-md1-ma-ma1] mep ccm-send enable
[PE1-md-md1-ma-ma1] remote-mep ccm-receive enable
[PE1-md-md1-ma-ma1] quit
# Configure PE2.
[PE2] cfm enable
[PE2] cfm version standard
[PE2] cfm md md1
[PE2-md-md1] ma ma1
[PE2-md-md1-ma-ma1] ccm-interval 30
[PE2-md-md1-ma-ma1] map vsi ldp1
Issue 02 (2014-09-30)
NOTE
When you run the qinq termination command on the same main interface, the ce-vid values must be
different if the pe-vid values of the two sub-interfaces are the same.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
8 Ethernet OAM Configuration
582