Huawei NetEngine80E Configuration Manual - Reliability page 225

HUAWEI NetEngine80E/40E Router
Configuration Guide - Reliability
4.
Issue 02 (2014-09-30)
preempt : yes delay time : 0
TimerRun : 1
TimerConfig : 1
Auth Type : NONE
Virtual Mac : 0000-5e00-0101
Check TTL : YES
Config type : admin-vrrp
Run the display vrrp binding admin-vrrp member-vrrp command on NPEs. You can
view the binding relationships between the mVRRP backup group and the member VRRP
backup groups.
Take NPE1 as an example.
[NPE1] display vrrp binding admin-vrrp member-vrrp
Interface: Virtual-Ethernet2/0/1, admin-vrrp vrid: 1, state: Master
Member-vrrp number: 1
Interface: Virtual-Ethernet2/0/5, vrid: 3, state: Master
Interface: Virtual-Ethernet2/0/3, admin-vrrp vrid: 2, state: Backup
Member-vrrp number: 1
Interface: Virtual-Ethernet2/0/7, vrid: 4, state: Backup
Configure the Peer BFD between NPEs.
# Configure NPE1.
[NPE1] bfd
[NPE1-bfd] quit
[NPE1] bfd peer1 bind peer-ip 192.168.1.2
[NPE1-bfd-session-peer1] discriminator local 341
[NPE1-bfd-session-peer1] discriminator remote 431
[NPE1-bfd-session-peer1] min-tx-interval 30
[NPE1-bfd-session-peer1] min-rx-interval 30
[NPE1-bfd-session-peer1] commit
[NPE1-bfd-session-peer1] quit
[NPE1] bfd peer2 bind peer-ip 192.168.2.2
[NPE1-bfd-session-peer2] discriminator local 342
[NPE1-bfd-session-peer2] discriminator remote 432
[NPE1-bfd-session-peer2] min-tx-interval 30
[NPE1-bfd-session-peer2] min-rx-interval 30
[NPE1-bfd-session-peer2] commit
[NPE1-bfd-session-peer2] quit
# Configure NPE2.
[NPE2] bfd
[NPE2-bfd] quit
[NPE2] bfd peer1 bind peer-ip 192.168.1.1
[NPE2-bfd-session-peer1] discriminator local 431
[NPE2-bfd-session-peer1] discriminator remote 341
[NPE2-bfd-session-peer1] min-tx-interval 30
[NPE2-bfd-session-peer1] min-rx-interval 30
[NPE2-bfd-session-peer1] commit
[NPE2-bfd-session-peer1] quit
[NPE2] bfd peer2 bind peer-ip 192.168.2.1
[NPE2-bfd-session-peer2] discriminator local 432
[NPE2-bfd-session-peer2] discriminator remote 342
[NPE2-bfd-session-peer2] min-tx-interval 30
[NPE2-bfd-session-peer2] min-rx-interval 30
[NPE2-bfd-session-peer2] commit
[NPE2-bfd-session-peer2] quit
After the configuration is complete, run the display bfd session all command on NPEs.
You can view that the status of BFD is Up.
Take PE1 as an example.
[NPE1] display bfd session all
-------------------------------------------------------------------
Local Remote PeerIpAddr
-------------------------------------------------------------------
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
State Type
4 VRRP Configuration
InterfaceName
208