Table of Contents
Advertisement
A
B
There is +24 VDC at P/J803-2 on the Tray PWB.
Y
N
Go to
Flag 7
on BSD 7.6 and check the harness for an open circuit. If the harness is
good, replace the Tray 2 Nudger Solenoid
Press Start. The voltage at P/J803-2 goes to approximately 0 VDC.
Y
N
Press Start. There is +5 VDC at P/J801B-11 of the Tray PWB.
Y
N
Go to
Flag 8
on BSD 7.6 and check the harness for an open or short circuit. If
the harness is good, replace the IOT Drive PWB
Replace the Tray PWB
(PL
9.3).
Replace the Tray 2 Nudger Solenoid
Enter dC330 008-014 Tray 2 Take Away Feed Clutch. Press Start and Stop several times.
The Tray 2 Takeaway Feed Clutch energizes.
Y
N
Press the Stop button. There is +24 VDC at P/J802B-14 on the Tray PWB.
Y
N
Replace the Tray PWB
(PL
9.3).
There is +24 VDC at P/J802B-13 on the Tray PWB.
Y
N
Go to
Flag 5
on BSD 8.2 and check the harness for an open circuit. If the harness is
good, replace the Tray 2 Takeaway Feed Clutch
Press the Start button. The voltage at P/J802B-13 goes to approximately 0 VDC.
Y
N
There is +5 VDC at P/J801B-8 on the Tray PWB.
Y
N
Go to
Flag 6
on BSD 8.2 and check the harness for an open circuit. If the har-
ness is good, replace the IOT Drive PWB
Replace the Tray PWB (PL 9.3).
Replace the Tray 2 Takeaway Feed Clutch
Check/replace the Tray 2 Feeder Assembly
broken, binding, or slipping.
Status Indicator RAPs
8-109 Tray 2 Prefeed Sensor On Jam RAP, 8-110 Tray
(PL
2.5).
(PL
9.2).
(PL
2.5).
(PL
2.7A).
(PL
9.2).
(PL
2.7A).
(PL
2.4). Replace any components that are worn,
8-110 Tray 2 Feed Out Sensor On Jam RAP
The Tray 2 Feed Out Sensor did not detect paper within the specified time after the prefeed
started.
Initial Actions
•
Refer to BSD 8.2 and BSD 8.10 for the following procedure.
•
Check for any obstructions in the paper path.
•
Open the Lower Left Door
Procedure
Cheat the L/H Cover Interlock Switch. Enter dC330 008-110 Tray 2 feed out Sensor and
press Start. Actuate the Tray 2 Feed Out Sensor. The display changes from L to H.
Y
N
The display indicates a constant H.
Y
N
Go to
Flag 3
on BSD 8.2 and check the harness for a short circuit. If the harness is
good, replace the Tray 2 Feed Out Sensor
Connect the meter from P/J415A-7 on the IOT Drive PWB to machine frame. Actuate the
Tray 2 Feed Out Sensor. The voltage at P/J415A-7 goes from less than +1.0 VDC
when the sensor is not actuated, to +5.0 VDC when the sensor is actuated.
Y
N
There is +5 VDC between P/J802A-9 and P/J802A-7 on the Tray PWB.
Y
N
Go to
Flag 4
on BSD 8.2 and check the harness for a short circuit. If the har-
ness is good, replace the Tray PWB
Go to
Flag 3
and
Flag 4
harness is OK, replace the Tray 2 Feed Out Sensor
ues, replace the Tray PWB
PWB
(PL
9.2).
Replace the IOT Drive PWB
Enter dC330 008-014 Tray 2 Take Away Feed Clutch. Press Start and Stop several times.
The Tray 2 Takeaway Feed Clutch energizes.
Y
N
Press the Stop button. There is +24 VDC between P/J802B-14 on the Tray PWB and
GND.
Y
N
Replace the Tray PWB
There is +24 VDC between P/J802B-13 on the Tray PWB and GND.
Y
N
Go to
Flag 5
on BSD 8.2 and check the harness for an open circuit. If the harness is
good, replace the Tray 2 Takeaway Feed Clutch
Press the Start button. The voltage at P/J802B-13 goes to approximately 0 VDC.
A
1/05
2-84
manuals4you.com
manuals4you.com
(PL
2.8).
(PL
2.8).
(PL
9.3).
on BSD 8.2 and check the harness for an open circuit. If the
(PL
2.8). If the problem contin-
(PL
9.3). If the problem continues, replace the IOT Drive
(PL
9.2).
(PL
9.3).
(PL
2.7A).
DocuColor 12/DCCS50
Reissue
Advertisement
Table of Contents
Troubleshooting
